Location of Controls
1. ON/OFF/DIMMER Switch
2. Adjustable Light Head
3. Adjustable Neck
4. Battery Compartment*
5. Adjustable Base/Mounting Bracket
*In back of unit
Installation
Hook and Loop Tape (included)
NOTE:
Hook and loop tape may be cut to desired size for easier removal.
1. Check the location of where you want to place the spotlight.
Make sure it is clean and there is no debris or dust.
2. Remove the paper covering to expose one sticky side of the tape.
3. Place the hook and loop tape in the recessed area on the mounting bracket.
4. Remove the paper covering on the other side of the tape to expose the sticky surface.
5. Place the spotlight in the desired location. Press firmly for five (5) seconds so the tape adheres to the surface.
CAUTION:
Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or
damage surface.
Detachable Bracket and Screws (included)
1. Remove the hook and loop tape by pulling the tape away from the mounting bracket.
2. Remove the printed mounting bracket template to use as a guide. Drill two (2) pilot holes in the location where you want to mount
the spotlight.
3. Remove the mounting bracket so it can be mounted. To do so, hold the spotlight base in one hand, with the mounting bracket fac-
ing up. With the other hand grab finger grips (Fig. 1) on mounting bracket and pull away from the spotlight. The cover will pop off.
You may also use a flathead screwdriver to gently pry off the mounting bracket.
NOTE:
It may help to turn the spotlight base clockwise or counter-clockwise as you are pulling it off.
4. Place screws (included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way. Align and slide the keyhole
slots on the mounting bracket over screw heads. Slide the bracket so the narrow ends of the keyhole slots are under the screw
heads. Tighten screws to secure mounting bracket to mounting surface. Take care to not over tighten.
5. Re-attach the spotlight to the detachable bracket. It will snap into place.
NOTE:
The base of the spotlight also acts as a stand so it can be placed on desk tops, table tops, just about anywhere!
Operating Directions
Universal Light Positioning
• Point the light head up, down or any angle in between by adjusting the light head accordingly.
• Turn the base to the left or right to point the light right where you need it.
• Slide the light neck in or out to adjust the height of the light head.
ON/OFF/DIMMER Operation
• Press power symbol once for full brightness.
• Press again for softer light.
• Press a third time to turn the light off.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove battery compartment cover on the back of the spotlight light head. To do so, hold the front of the spotlight in one hand,
with the other hand twist the battery cover counter clockwise
(in the direction of the “OPEN” arrow) and pull off.
2. Install three new AA batteries.
3. Make sure to follow battery polarity guide when installing new batteries.
4. Replace battery compartment cover by placing it back on the spotlight making sure that the “Open” and “Lock” markings are at
the top of the spotlight (Fig. 1). Twist it clockwise until it locks into position (in the direction of the “LOCK” arrow).
Battery Precautions:
1. Use only the size and type of batteries specified.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries
may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fire.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
LPL720/LPL720W Owner’s Manual
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Modifications to this product not approved by the party responsible for compliance could void the user’s authority to operate the product.
OPEN
LOCK
Fig. 1
AA BA
TTER
Y
AA BA
TTER
Y
AA BA
TTER
Y
Mounting Surface
Unit
Mounting
Bracket
Screw
Screw
Mouting Bracket
Keyhole Slots
Finger Grips
Fig. 1
2
4
5
3
1
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express
warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The Limited Warranty
is in lieu of all other express or implied warranties or liabilities subject to the exceptions explained fully in the Limited
Warranty on the website.
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0098-A
WIRELESS LED “SPOTLIGHT”
