Weber GENESIS 3000 LX Owner'S Manual Download

Page: 1 / 36

Serial Number

Please use this number in registering your warranty
and any correspondence with the factory.

W
E

GENESIS

3000 LX

Natural Gas Barbecue

Owner’s Manual

98648

10/97

FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.

NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.

WARNING: Follow all leak check procedures
carefully in this manual prior to barbecue
operation. Do this even if barbecue was
dealer assembled.

WARNING: Do not try to light this appliance
without reading "Lighting" instructions
section of this manual.

THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.

FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your

gas supplier or your fire department.

Summary of Contents for GENESIS 3000 LX





































Search results

Summary of Contents for GENESIS 3000 LX

Reviews:

Related manuals for GENESIS 3000 LX

Brands by name

Popular brands

Weber GENESIS 3000 LX, Owner'S Manual

Search results

Summary of Contents for GENESIS 3000 LX

Reviews:

Related manuals for GENESIS 3000 LX

Brands by name

Popular brands