background image

Waterco Limited ABN 62 002 070 733

www.waterco.com

ZZM1461_06/2014

OFFICES - AUSTRALIA

NSW - Sydney
(HEAD OFFICE) 

 

Tel : +61 2 9898 8686
VIC/ TAS - Melbourne
Tel : +61 3 9764 1211
WA  - Perth
Tel : +61 8 9273 1900
QLD - Brisbane
Tel : +61 7 3299 9900
SA/ NT - Adelaide
Tel : +61 8 8244 6000
ACT Distributor
Tel : +61 2 6280 6476

OFFICES - OVERSEAS

Waterco USA
Augusta, USA
Tel : +1 706 793 7291
Waterco Canada
Longueuil, Qc, Canada
Tel : +1 450 748 1421
Waterco (Europe) Limited
Sittingbourne, Kent. UK 
Tel : +44(0) 1795 521 733
Waterco France
SAINT PRIEST, France 
Tel : +33 (0)4 72 79 33 30
Waterco (NZ) Limited
Auckland, New Zealand
Tel : +64 9 525 7570

Waterco (C) Limited
Guangzhou, China
Tel : +8620 3222 2180
Waterco (Far East) Sdn. Bhd.
Selangor, Malaysia
Tel : +60 3 6145 6000
PT Waterco Indonesia
Jakarta, Indonesia
Tel : +62 21 4585 1481
Waterco International Pte Ltd
Singapore
Tel : +65 6344 2378

125

INSTALLATION AND 

USER’S GUIDE 

(AUSTRALIA)

240 VAC NATURAL GAS/LP GAS
MODELS TT125

 

Natural

 

Propane

125K (33kW) with cord 

2701251  2701252

FOR YOUR SAFETY - READ BEFORE OPERATING

•  If you do not follow these instructions exactly, a fire or explosion may result, causing 

property damage, personal injury or loss of life.

•  Improper installation, adjustment, alteration, service or maintenance can cause property 

damage, personal injury or death. Installation and service must be performed by a qualified 
installer, service agency or the gas supplier.

•  Do not place articles or against this appliance.
•  Do not use or store flammable materials near this appliance.
•  Do not spray aerosols in the vicinity of this appliance while it is in operation.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any phone in your building.
•  Immediately call your gas supplier from a neighbor’s phone.
  Follow the gas supplier’s instructions.
•  If you cannot reach your gas supplier, call the fire department.

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or 
other appliances.

!

WARNING

!

WARNING

Improper installation, adjustment, alteration,
service or maintenance can cause property 

damage, personal injury or death. Installation and service must be 
performed by a qualified installer, service agency or the gas supplier.

FOR YOUR SAFETY - READ BEFORE OPERATING

If you do not follow these instructions exactly, a fire or explosion may result, causing property 
damage, personal injury or loss of life. For additional free copies of this manual; call Waterco 
Limited.

FOR YOUR SAFETY - This product must be installed and serviced by authorized personnel, qualified in pool/spa heater 
installation. Improper installation and/or operation can create carbon monoxide gas and flue gases which can cause 
serious injury, property damage, or death. For indoor installations, as an additional measure of safety, Waterco Limited 
strongly recommends installation of suitable Carbon Monoxide Detectors in the vicinity of this appliance and in any 
adjacent occupied spaces. Improper installation and/or operation will void the warranty.

!

WARNING

Summary of Contents for Turbotemp 125































Reviews: