background image

DUPLICATOR 9

GETTING

Thanks for choosing Wanhao 3D Printer products. You’re just moments away from printing your first 3D

model. It’s important that you follow these steps carefully to ensure correct setup of your 3D Printer.

STARTED

GUIDE

You can also visit 

www.wanhao3dprinter.com/Video/D9 video/wanhao D9 unboxing 

for step by step guide on unboxing and setup, levelling, filament installation and printing.

Package Contents:

1 x WANHAO 3D Printer 

1 x Filament Spool Holder

1 x Filament Spool Stand

1 x Power Cable

1 x USB Cable

1 x 8GB SD Card

1 x Hex Screw Driver

1 x Hex Key Set

6 x Hex Bolts

2 x Plastic belts

1 x 1.75mm PLA Filament

1 x Needle for unclugging nozzle

ASSEMBLING AND MOUNTING

1

Take out all components 

from the box and 

place them on the flat 

ground.

1-Base 

2-Z axis Tower Pillar*2

3-X axis rail

4-X axis gantry

5-MK12 Extruder

Place the Base on 

it’s side. Find the Z 

axis pillar with sticker 

No.2.  Slide the No.2 

pillar into the base 

vertical locker. Then 

tighten the bolt at 

bottom of base.  

2

A

D

4

5

6

Insert the leveling 

card or an A4 paper 

between the nozzle 

and bed.  Adjusting 

the Z axis height, 

until you can feel the 

friction while moving 

the card or paper. 

Click the upper Z to move 

extruder up and click the 

lower Z to move extruder 

down. Stop clicking until 

you feel the leveling card 

getting friction while 

moving the card.  

Click NEXT to initiate 

auto leveling. 

7

Congratulation! You have finished bed leveling. For video installation, 

please scan the QR code. 

Video Installation

Official Website

Wanhao Store

To move the extruder 

by hand to 4 corners 

separately.  Adjusting 

the knob at each 

corner, until you feel 

friction while moving 

the leveling card. 

Summary of Contents for DUPLICATOR 9

Page 1: ...ng Package Contents 1 x WANHAO 3D Printer 1 x Filament Spool Holder 1 x Filament Spool Stand 1 x Power Cable 1 x USB Cable 1 x 8GB SD Card 1 x Hex Screw Driver 1 x Hex Key Set 6 x Hex Bolts 2 x Plastic belts 1 x 1 75mm PLA Filament 1 x Needle for unclugging nozzle ASSEMBLING AND MOUNTING 1 Take out all components from the box and place them on the flat ground 1 Base 2 Z axis Tower Pillar 2 3 X axi...

Page 2: ...llars If any bolt not secured You need to secure the screws to ensure the gantry are steady and tight Rotate the cylinder holder for a bit but not too close Tight enough that can not slide into pillar freely This is also same to the other side with stickers No 6 8 9 Mount the X axis rail Align the right and left side holders first Please make sure the rail is located in the middle of the X axis Yo...

Page 3: ...n order to level the two Z axis at same height Note The ruler or height gauge would provide more accurate height for both two Z axis The two axis need to be at same height 3 Turn on the printer Release the 4 bed leveling nuts by 4 5 turns Then Click LEVEL Read the instruction then click NEXT ...

Page 4: ...o move extruder down Stop clicking until you feel the leveling card getting friction while moving the card Click NEXT to initiate auto leveling 7 Congratulation You have finished bed leveling For video installation please scan the QR code Video Installation Official Website Wanhao Store To move the extruder by hand to 4 corners separately Adjusting the knob at each corner until you feel friction w...

Reviews: