background image

CEF40/75 FRYER

- NOTICE -

This  Manual  is  prepared  for  the  use  of  trained  Vulcan  Service
Technicians  and  should  not  be  used  by  those  not  properly
qualified.

This manual is not intended to be all encompassing. If you have
not attended a Vulcan Service School for this product, you should
read, in its entirety, the repair procedure you wish to perform to
determine if you have the necessary tools, instruments and skills
required to perform the procedure. Procedures for which you do
not  have  the  necessary  tools,  instruments  and  skills  should  be
performed by a trained Vulcan Service Technician.

The  reproduction,  transfer,  sale  or  other  use  of  this  Manual,
without the express written consent of Vulcan, is prohibited.

This manual has been provided to you by ITW Food Equipment
Group LLC ("ITW FEG") without charge and remains the property
of ITW FEG, and by accepting this manual you agree that you will
return it to ITW FEG promptly upon its request for such return at
any time in the future.

SERVICE MANUAL

A product of Vulcan-Hart

3600 North Point Blvd Baltimore, MD 21222

F45657 (0517)

Summary of Contents for CEF40


























Reviews: