background image

V

ULCAN

WARRANTY

WARRANTY: Except with respect to those components parts and uses
which are hereinafter described, Degussa-Ney Dental Inc. (Degussa-Ney)
warrants this furnace to be free from defects in material and workmanship
for a period of two years from the date of sale.  Degussa-Ney ’s liability
under this warranty is limited solely to repairing or, at Degussa-Ney ’s
option, replacing those products included within the warranty which are
returned to Degussa-Ney  within the applicable warranty period (with
shipping charges prepaid), and which are determined by Degussa-Ney  to
be defective.  This warranty shall not apply to any product which has
been subject to misuse; negligence; or accident; or misapplied; or
modified; or repaired by unauthorized persons; or improperly installed.

INSPECTION: Buyer shall inspect the product upon receipt.  The buyer
shall notify Degussa-Ney  in writing of any claims of defects in material
and workmanship within thirty days after the buyer discovers or should
have discovered the facts upon which such a claim is based.  Failure of
the buyer to give written notice of such a claim within this time period
shall be deemed to be a waiver of such claim.

DISCLAIMER: The provisions here-in stated Degussa-Ney  sole obliga-
tion and exclude all other remedies or warranties, expressed or implied,
including those related to 

MERCHANTABILITY and FITNESS FOR A

PARTICULAR PURPOSE.

LIMITATION OF LIABILITY: Under no circumstances shall Degussa-
Ney   be liable to the buyer for any incidental, consequential or special
damages, losses or expenses.

LIMITATION OF ACTIONS: The buyer must initiate any action with
respect to claims under the warranty described in the first paragraph
within one year after the cause of action has accrued.

Corporate and Sales Office:

Product Service Office:

DEGUSSA-NEY DENTAL INC.

DEGUSSA-NEY DENTAL INC.

65 West Dudley Town Road

Equipment Division

Bloomfield, CT 06002-1316 USA

13553 Calimesa Blvd.

860.242.6188

Yucaipa, CA 92399-2303 USA

FAX 860.769.5050

909.795.2461

FAX 909.795.5268

ABOX  9942 93-63-047

Owner's & Operator's Manual

Models:

A-130

A-550

A-1750

100V

---

9493486

---

100-120V

9493300

---

---

120V

---

9493306

---

200-240V

9493301

9493307

9493407

230 (EURO)

---

---

9493657

TM

BOX FURNACE

 

with

 

Automatic Controls

Ney

Summary of Contents for A-130







Reviews: