NOTES:
1. Use only the power adapters and batteries supplied with your
VTech telephone.
2. For complete feature instructions, please refer to your user’s manual.
96-006499-050-100
IMPORTANT!
If your product is not working properly:
Refer to the
Troubleshooting
section of the user’s
manual.
Visit our website at www.vtechphones.com.
In Canada, go to www.vtechcanada.com.
Call our customer service at 1 (800) 595-9511.
In Canada, call 1 (800) 267-7377.
•
•
•
Telephone base & charger installation
We recommend that you install the telephone base away from
any electronic equipment and appliances such as personal
computers, computer routers, television sets, microwave ovens
or refrigerators. Avoid excessive heat, cold, dust or moisture.
Install the telephone base and charger as illustrated. Make
sure that the electrical outlet is not controlled by a wall switch.
If you subscribe to Digital Subscriber Line (DSL) high-speed
Internet service through your telephone line, you must have a
DSL filter between the telephone base and the telephone wall
jack. The filter prevents noise and caller ID problems caused
by DSL interference. Please contact your DSL service provider
for more information about DSL filters.
Make, receive and end calls
Make a call
• Press
/
FLASH
or , listen for a dial tone, then dial the
telephone number.
-OR-
1. Dial the number (press
MUTE/REMOVE
to make
corrections; press and hold
REDIAL/PAUSE
to insert a
dialing pause).
2. Press
/FLASH
or to use the speakerphone.
Receive a call
• Press
/
FLASH
, or any dialing keys (
0
-
9
,
*
or
#
) to
answer an incoming call.
End a call
• Press
OFF/CLEAR
or put the handset back in the telephone
base or charger.
Voicemail setup
If you subscribe to voicemail service provided by your local
telephone company, this feature allows you to use the
VOICEMAIL
,
PLAY
,
SKIP
and
ERASE
buttons to access
your voicemail. Before completing these steps, be sure
to have your access number and password (provided by
your local telephone company) to access your voicemail.
You will also need the codes to play, skip and erase your
messages. Contact your local telephone company for more
information.
To program the
ACCESS NUMBER
button:
1. Press
MENU/SELECT
when the handset is not in use.
2. Press or to select
VOICEMAIL SETUP
, then press
MENU/SELECT
.
3. Press or to select
ACCESS NUMBER
, then press
MENU/SELECT
.
4. Use the dial pad to enter the access number. Press
MUTE/REMOVE
to delete characters if necessary.
5. Press
MENU/SELECT
. You will hear a confirmation tone.
To program the
PASSWORD
,
PLAY
,
SKIP
and
ERASE
buttons, follow steps 1 and 2 above. Next, select the
command you wish to program, and press
MENU/SELECT
.
Use the dial pad to enter the corresponding code for that
command, and press
MENU/SELECT
to confirm.
To program a pause (for more details, refer to the user’s
manual):
1. Press
MENU/SELECT
when the handset is not in use.
2. Press or to select
VOICEMAIL SETUP
, then press
MENU/SELECT
twice.
3. The blinking cursor should be at the end of your access
number. Press and hold the
REDIAL/PAUSE
button until
a
P
appears.
4. Press
MENU/SELECT
. You will hear a confirmation tone.
NOTE:
You must program your voicemail buttons before you can access all
of the functions available with your voicemail.
Battery installation & charging
Install the handset battery by following these steps:
1. Press the tab and slide the battery compartment cover down.
2. Align the two holes of the battery plug with the socket pins
in the handset battery compartment, matching the red and
black wires of the color-coded label.
3. Place the battery in the compartment with the wires in the
lower right corner.
4. Align the cover flat against the battery compartment, then
slide it up until it clicks into place.
For optimal performance, we recommend that you charge
the handset for 16 hours. You can keep the battery charged
by returning the handset to the telephone base or charger
after use. When the battery power is fully depleted, a full
recharge takes about 16 hours.
Quick start guide
for models DS3111-2/TM3111-2
Charger adapter
Electrical outlet not
controlled by a wall
switch
Plac e the hand set in the
telephone base or charger. The
CHARGE
light is on when the
handset is properly positioned in
the telephone base or charger.
CHARGE
light
Telephone base
power adapter
CHARGE
light
BT8000/ BT6010
Telephone
wall jack
Electrical outlet
not controlled by
a wall switch
Telephone base power adapter
Charger adapter
Telephone line
cord
MANUFA
CTURED IN CHINA
COMPLIES WITH 47 CFR PA
RT 68
REGISTRATION NO.: US:EW7W401B80-565600
RINGER EQUIVA
LENCE: 0.1B
USOC JACK: RJ11C/RJ1
1W
HAC FCC ID: EW780-5656-00
THIS DEVICE COMPLIES WITH PA
RT 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO
THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY
NOT CAUSE HARMFUL
INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT
MAY
CAUSE UNDESIRED OPERAT
ION. PRIVA
CY OF
COMMUNICAT
IONS MAY
NOT BE ENSURED WHEN USING THIS PHONE.
DC 6V 300mA
CLASS 2 POWER SOURCE ONLY
TELEPHONE
EQUIPMENT
DSL filter (not
included) required
if you have DSL
high-speed
internet service
