VPC i2 MICRO iCON User Manual Download

Page: 1 / 20

INDEX

(CLICK TO NAVIGATE TO PAGE)

PAGE

RECEIVER PART IDENTIFICATION

ITA PART IDENTIFICATION

RECEIVER/ITA ENGAGEMENT & DISENGAGEMENT

RECEIVER MOUNTING

ITA COVER REMOVAL

ITA COVER INSTALLATION

CABLE CLAMP REMOVAL & INSTALLATION

CONTACT REMOVAL

RECEIVER STRAIN RELIEF ASSEMBLY

RECEIVER PROTECTIVE COVER INSTALLATION

ITA PROTECTIVE COVER INSTALLATION

KEYING PIN KIT, RECEIVER & ITA ASSEMBLY

PCB ASSEMBLY W/ TWO HEADERS

PCB LAYOUT W/ HEADER

STANDARD PCB LAYOUT

HYBRID PCB LAYOUT W/ HEADER

HYBRID STANDARD PCB LAYOUT

TROUBLESHOOTING

i2 MICRO iCON USER MANUAL

07/23/21

Please note that any printed or downloaded User Manuals may not reflect the most current

revisions. The information contained in this material is subject to change.

The most current information available will be on vpc.com.

Summary of Contents for i2 MICRO iCON





















Search results

Summary of Contents for i2 MICRO iCON

Reviews:

Related manuals for i2 MICRO iCON

Brands by name

Popular brands

VPC i2 MICRO iCON, User Manual

Search results

Summary of Contents for i2 MICRO iCON

Reviews:

Related manuals for i2 MICRO iCON

Brands by name

Popular brands