Viking FREEDOM VK490 Technical Data Manual Download

Page: 1 / 34

FREEDOM

RESIDENTIAL

CONCEALED HORIZONTAL

SIDEWALL SPRINKLER VK490

(K5.8)

TECHNICAL DATA

The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058

Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: [email protected]

Visit the Viking website for the latest edition of this technical data page.

Form No. F_032116 Rev 01 September 7, 2022

Page 1 of 7

1. DESCRIPTION

Viking Freedom

Residential Concealed Horizontal Sidewall Sprinkler VK490

is a small high-sensitivity solder link and lever residential sprinkler designed for

installation on concealed pipe systems, where the appearance of a smooth wall is

desired. The sprinkler orifice design, with a K-Factor of 5.8 (83.6 metric*), allows

the sprinkler’s efficient use of available water supplies for the hydraulically designed

fire-protection system. The operating element and special deflector characteristics

meet the challenges of residential sprinkler standards.

The sprinkler is hidden from view by a low profile, small diameter cover plate

installed flush to the wall. The cover plate is available in several decorative finishes

to meet design requirements. The two-piece design allows installation and testing of

the sprinkler prior to installation of the cover plate. After the system has been tested

and wall finish has been applied, the push-on design of the cover plate assembly

allows easy installation of the cover plate with up to 1/4” (6.4 mm) adjustment.

Sprinkler VK490 is provided with a pipe guide to properly locate the sprinkler and

allow the 1/4” adjustment of the cover plate.

2. LISTINGS AND APPROVALS

UL Listed (C-UL-US-EU):

Category VKKW (VK490)

Refer to the Approval Chart and Design Criteria for C-UL-US-EU Listing

requirements that must be followed.

3. TECHNICAL DATA

Specifications:

Available since 2016.

Minimum Operating Pressure: Refer to the Approval Chart.

Maximum Working Pressure: 175 psi (12 bar). Factory tested hydrostatically to 500 psi (34.5 bar).

Thread size: 1/2” (15 mm) NPT

Nominal K-Factor: 5.8 U.S. (83.6 metric*)

* Metric K-factor measurement shown is in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0.

Available Cover Plate Horizontal Adjustment: 1/4” (6.4 mm)

Overall Length (Sprinkler Body): 2” (50 mm)

Covered by the following U.S. Patent numbers: 7,854,269; 7,712,218 and 8,960,319

Material Standards:

Sprinkler Body: QM Brass and Brass UNS-C84400

Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with

Polytetrafluoroethylene (PTFE)

Tape

Seat: UNS-C31400 or Brass UNS-C31600, ENT coating available upon request

Deflector Ring: Brass UNS-C23000

Deflector Pins: Stainless Steel UNS-S30200

Halo: Phosphor Bronze UNS-C51000, e-coating available upon request

Flow Shaper: Phosphor Bronze UNS-C51000

Lever Bar Ring: Brass UNS-C84400 or UNS-C31600

Compression Screw: 18-8 Stainless Steel

Fusible Link Assembly: Nickel Alloy and Eutectic Solder

Fusible Link Levers: Stainless Steel UNS-S31600

Guide Pin: Stainless Steel UNS-S43000, ENT coating available upon request

Shipping Cap: Polyethylene

Cover Assembly Materials:

Cover Plate Assembly: Copper UNS-C11000 and Brass UNS-C26800

Spring: Beryllium Nickel

Solder: Eutectic

Ordering Information:

(Also refer to the current Viking price list.)

Viking Freedom

Residential Concealed HSW Sprinkler VK490 and Cover Plate Assembly must be ordered separately:

Sprinkler:

Base Part No. 20409.

Finish Suffix: Brass = A

Temperature Suffixes: 165 °F (74 °C) = C, 205 °F (96 °C) = E

Replaces Form No. F_032116 Rev 22.1

(Updated UL cover plate temperature rating.)

Summary of Contents for FREEDOM VK490



































Search results

Summary of Contents for FREEDOM VK490

Reviews:

Related manuals for FREEDOM VK490

Brands by name

Popular brands

Viking FREEDOM VK490, Technical Data Manual

Search results

Summary of Contents for FREEDOM VK490

Reviews:

Related manuals for FREEDOM VK490

Brands by name

Popular brands