background image

Table of Contents

 

Rev. 4/22/2019 

   FMDL MANUAL 

 

Table of Contents

 

Copyright 2019   Vestil Manufacturing Corp.  

 

Page 1 of 16 

 

 

 

 
  

 

 

 

 

 

 

 

FMDL-Series Single & Double Eagle Beak Fork-Mounted Drum Lifters

 

Use and Maintenance Manual

 

 

 

 

            

            

 

                   

FMDL-1 (Eagle beak™)            FMDL-2 (Eagle Beak™)            FPDL-8-L (Base Engaging 

                                                                                                                             Plastic Barrel Handler) 

 

                         

 

                          FPDL-11-H (Top Engaging Plastic               DFDL-3 (Eagle Beak™, Top, & Base 

                          Barrel Handler)                                                  Engaging Barrel Handler) 

 

Receiving instructions: 

 

After delivery, remove the packaging from the product. Inspect the product closely to determine whether 

it sustained damage during transport. If damage is discovered, record a complete description of it on the 

bill of lading. If the product is undamaged, discard the packaging.

 

 

NOTE:

 

The end-user is solely responsible for confirming that product design, use, and maintenance comply with 

laws, regulations, codes, and mandatory standards applied where the product is used.

 

 

Technical Service and Replacement Parts:  

  For answers to questions not addressed in these instructions and to order replacement parts, labels, 

and accessories, call our Technical Service and Parts Department at (260) 665-7586. The department can 

also be contacted online at 

http://www.vestilmfg.com/parts_info.htm

. 

 

 

Table of Contents 

Table of Diagrams 

 

Specifications

…….……………........... 

2

   

FMDL-1 parts diagram and bill of materials

…………….……

3

 

Signal Words

………………..…........... 

2

 

FMDL-2 parts diagram and bill of materials

.…....…........... 

4

 

Hazards

…………………..……............... 

2

 

FPDL-11-H parts diagram and bill of materials

……….…...… 

5

 

Using the Lifter

.……………..…………..

11

 

FPDL-8-L parts diagram and bill of materials

……….….……

6

 

Record of Original Condition

.....….. 

11

 - 

12

 

DFDL-3 parts diagram and bill of materials

…………............

7

 

Inspections & Maintenance

...……….

12

 

Centers of Gravity Diagrams

………….……....…………

8

9

, 

10

  

Optional Equipment

…………….

   

13

14

15

 

Labeling Diagram

…………………………….………………

 

12

 

Limited Warranty

………………………… 

16

 

Vestil Manufacturing Corp. 

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 

Telephone: (260) 665-7586  -or-  Toll Free (800) 348-0868 

Fax: (260) 665-1339 

Web: 

www.vestilmfg.com

             Email: 

[email protected]

 

 

Summary of Contents for DFDL-3

















Reviews: