background image

AVMOD8                                                                                                                                                                               NL 

AVMOD8 – 2.4GHz WIRELESS A/V TRANSMITTER/RECEIVER WITH IR REMOTE CONTROL 

 

1.  Contents 

 

 

Transmitter (AVMOD8TX) 

 

Receiver (AVMOD8RX) 

 

IR mouse / transmitter 

 

Two A/V cables (RCA to SCART for PAL) 

 

Two mains adapters 

 

Adhesive strip (to fix the IR transmitter) 

 

Detailed manual 

 
 

2.  Description 

 
The transmitter and receiver look very much alike. Find the nametag with ‘AVMOD8TX’ (= transmitter) or ‘AVMOD8RX’ (= 
receiver). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  1.  ON/OFF LED : this LED is lit when the ON/OFF switch is in the ON position. 
  2.  2.4GHz A/V antenna (front) : Transmits A/V signals. Attention : the antenna will only turn 270° (see “Orienting devices” 

on p. 6). 

  3.  Connection for IR transmitter 
  4.  Channel switch : Select the desired channel number. Remember to select the same channel on both transmitter and 

receiver. 

  5.  Audio left jack (white) 
  6.  Audio right jack (red) 
  7.  Video jack (yellow) 
  8.  9V adapter jack 
  9.  ON/OFF switch 
10.  Channel switches : Place the channel switch in the ON position to select the channel. Switch  5 sets the timer for the 

autosequence function. Select the same channel number for transmitter and receiver. 

 

front transmitter 

back transmitter 

front receiver 

back receiver 

 

 

Summary of Contents for AVMOD8








Reviews: