background image

Doc. # 01

-

04

-

033A

 

Vastex International, Inc.

 

7 Emery St

Bethlehem, Pa. 18015 USA 

Phone# 610 625-2702  Fax# 610 625-2775

 

Web Site  www.vastex.com

 

Authorized Representative in Europe:

 

Certification Experts BV

 

Nieuwstad 100 1381 CE Weesp, 

 

The Netherlands 

 

Tel :

 

+ 31 (0) 294 – 48 33 55 

 

Fax :

 

+ 31 (0) 294 – 41 46 87

 

Year of Manufacture: 

20____

 

Original Instructions

 

Serial Number:  

VTX

 

 

(Please log your machine's serial number and date of purchase for future reference.)

 

Date:

 

 

/

 

/

 

Electrical Drawing #: 

Revision:

  

Vastex E

-

mail assistance

Purchasing & Product Info:

 

[email protected]

 

Electrical Support:

 

[email protected]

 

Tech Support, Mechanical Setup, and Operation:

 

[email protected]

 

Screen Printing Issues & Support:

 

[email protected]

 

 

E

-

1000/E

-

2000 Exposing Units

Assembly and Operation Instructions

 

Contents

 

Pg. #

 

Introduction, Machine Specifications

2

 

Safety Information

3

 

Assembly Instructions

4

-

5

Operating Instructions

6

-

8

Maintenance

9

Troubleshooting

10

-

12

Emulsion Tips

13

-

14

Warranty/Terms and Conditions

15

E2

-

2536

 

E2

-

5236

 

Summary of Contents for E-1000
















Reviews: