Проверил: Р.Ч./19.03.2015г
JS98-A
1.
Soldering Tip
2.
Screw
3.
Light
4.
Switch
5.
Handle
6.
Plug
Technical Information
Power:
Voltage:
Frequency:
Insulation:
100W
220V-240V~
50Hz
Class II
Original User’s Manual
Before using the Gun, make sure your voltage and electric current frequency
match with the technical information above. The numbers shown here refer to
the illustration above.
1.
Using the
Cord (#6)
, connect the gun to a 230V/50Hz power supply.
2.
Holding the gun by the
Handle (#5)
place the
Solder Tip (#1)
on the
point you wish to solder.
3.
Turn on the
Switch (#4)
and the
Light (#3)
will shine on.
4.
It will take 6 to 8 seconds for the gun to reach temperature (230
degrees C).
5.
When finished soldering, turn off the
Switch (#4).
As you depress the
Switch (#4)
the gun will continue to heat up. Do not
depress the
Switch (#4)
for long periods of time while soldering.
When you let go of the
Switch (#4)
, the temperature diminishes quickly.
Depressing the
Switch (#4)
quickly raises the temperature.
Keeping the gun at a constant temperature extends the life of the gun.
Before using the gun, lubricate the
Soldering Tip (#1)
.
This gun is energy efficient as it reaches temperature very quickly.
The shape of the Soldering Tip (#1) allows you to partially contact the
workpeice.
Maintenance
The gun and the
Soldering Tip (#1)
are designed to easily disconnect for
occasional replacement.
Tip Replacement
Unscrew the two screws connecting the
Soldering Tip (#1)
to the gun. Pull
off the old tip, replace it, and replace the two screws.
Lamp Replacement
Attention:
1.
Before using, verify the electricity requirements and visually inspect
the gun and your workstand.
2.
Never use the gun. in the rain.
3.
Make sure no foreign objects are in the gun’s internal parts.
4.
Never dismantle the gun. Contact an authorized service technician.
5.
Disconnect the gun from the power source when not in use.
6.
This gun is primarily designed for indoor use.
Safety Instructions:
Warning, when using electric tools basic safety precautions should be
followed to reduce the risk of fire, electric shock, and personal injury. Read
the entire manual before attempting to operate the soldering gun. Save this
manual.
1.
Keep work area clean.
Cluttered areas and benches invite injuries.
2.
Consider work area environment.
Never expose power tools to rain. Do not use power tools in damp or wet
locations. Keep work area well lit. Don’t use power tools near flammable
liquids or gasoline.
3.
Guard against electric shock.
Prevent body contact with grounded surfaces (pipes, radiators, ranges,
refrigerators) when open operating power tools.
4.
Keep children away from power tools.
Do not let anyone contact the tool or the power cord. Keep all visitors out of
the work area.
5.
Store idle tools.
When not in use, tools should be stored in a dry, out of reach, or locked
location, away from children.
6.
Do not force tool.
It will operate move efficiently and safer at the normal rate it was designed
for.
7.
Use right tool.
Don’t force small tools to do the job of heavy tools. Operate tools for intended
use only.
8.
Dress Properly.
Do not wear loose clothing or jewelry. They may become caught in moving
parts. Rubber gloves and non-skid footwear are recommended when working
outdoors. Wear a protective hair covering to contain long hair.
9.
Use proper safety glasses.
If necessary, use a face shield or dust mask.
10.
Don’t abuse cord.
Never carry the tool by the cord or yank it out of a power receptacle. Keep
cord away from heat, all liquids, and sharp edges.
11.
Don’t overreach.
Keep proper footing and balance at all times.
12.
Maintain tools with care.
For safety and performance, keep tools clean and sharp. Follow regular
maintenance procedures. Inspect tool cords and extension cords periodically.
If damaged, use a certified service technician to repair. Keep handle dry, clean,
and free from grease or oil.
13.
Disconnect tools.
Disconnect when not in use, servicing, or performing maintenance.
14.
Remove adjusting keys and wrenches.
Before turning on the tool, make sure no adjustment keys or tools are
connected to the tool.
15.
Avoid unintentional starting.
Never carry a plugged in tool with your finger on the switch. Turn switch off
before plugging it in.
16.
Outdoor extension cords.
When working outdoors, use outdoor rated extension cords.
17.
Stay alert.
Use common sense. Pay attention to your work. Do not operate tool when
overtired.
18.
Check for damaged parts.
Before using, check the tool for damaged parts to insure safe operation. Check
alignment of moving parts, for broken parts, binding of moving parts, proper
mounting, and any conditions that might affect safe operation. Any guard or
part that is damaged should be replaced or repaired by a authorized service
technician. Do not use the tool if switch does not turn on or off properly. Have
defective switches replaced by an authorized service technician.
19.
Warning.
Use of any accessory or attachment other than those recommended in this
manual may present the risk of personal injury.
If the supply cord is damaged, it must be replaced by manufacturer, its service
agent or similarity qualified persons in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
20.
Authorized service technician repairs only.
This electric power tool is must only be repaired by an authorized service
center. Do not repair yourself or you may cause damage to the tool and put
yourself in danger.
Save these instructions.
Parts List
No.
Description
1
Soldering Tip
2
Movable elastic
3
Heat insulation fixed staff impipiece
4
Transformer
5
Cabinet(a)
6
Cabinet(b)
7
Nameplate
8
Screw
