Tools
Required:
Flathead
screwdriver,
Phillips
screwdriver,
pliers,
wire
cutters,
wire
strippers,
electrical
tape,
safety
glasses.
Light
Source:
(2) A19
Medium
Base
Bulbs
60W
Maximum, Alternate
Bulbs
(2)13W
CFL Maximum.
Estimated
Assembly
Time:
20-30
minutes
Preparation:
Identify
and
inspect
all
parts
before
beginning
installation.
Check
package
content
list
and
diagrams
below
to
be
sure
all
parts
are
present.
If
any
parts
are
missing
or
damaged,
do
not
attempt
to
assemble,
install,
or
operate
the
fixture.
Contact
customer
service
for
replacement
parts.
1of2
Package Contents
B
Crossbar
x 1
Lock Washer
x 1
Hex Nut
x 1
Nipple
x 1
A
F
Fixture Body
x 1
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
C
D
Knob
x 1
E
G
Glass Panel
x 1
STEP 1
Remove Cage
-
A. Remove Cage from the
Ceiling Canopy by unlocking
Lock Balls.
Ceiling
Canopy
Lock Ball
Cage
Figure 1
STEP 2
Install Crossbar
-
A.
A)
Attach the Crossbar (
to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included)
Tighten until snug
.
.
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
A
Figure 2
A
B
C
D
E
STEP 3
Install Nipple and Ceiling
Canopy
-
*
Pliers is required for this step.
A. Thread Hex Nut (C) to the middle of
the Nipple (D). Place Lock Washer (B)
over the Nipple (D) and then thread
the Nipple (D) into the Crossbar (A)
until the Nipple (D) is about 0.375”
above the Crossbar (A).
C. Place the Ceiling Canopy over the
Nipple (D) against the ceiling to
Ceiling
Canopy
(Step 3 Continued)
determine the correct position of the Nipple (D). Thread the Knob
(E) onto the Nipple (D). Adjust the Nipple (D) to allow the Ceiling
Canopy to rest against the ceiling when held in place by the Knob
(E).
D. Remove the Knob (E) and the Ceiling Canopy. Tighten the Hex Nut
(C) against the Crossbar (A) to secure in place.
E. Refer to Step 4 for wire connections.
F. Place the Ceiling Canopy back over the Nipple (D) and secure with
the Knob (E). Hand tighten until snug.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 - Install Bulbs and Cage
A. Place the Glass Panel (G) into the bottom of the Cage (G) properly.
B. This fixture uses standard bulbs with standard screw bases.
Maximum 60 watts.
C. Attach the Cage over the Bolts on the bottom of the Ceiling Canopy
Insert bulb and screw snugly into place.
Socket
Figure 5
Bolt
G
Cage
Lock
Ball
Ceiling
Canopy
and secure with Lock
Balls. Hand tighten until
snug.
Your fixture is now
assembled and ready to
use. Enjoy!
Installation Instructions:
UQL
124
9
www.urbanambiance.com
