Cable Remote Control
Operating Instructions For
CLIKR
TM
-5
Universal Remote Control, Inc.
www.universalremote.com
OCE-0060K Rev 04 (11/12/10)
1
1
Introduction
4
4
Button Functions
5
5
Programming the Remote Control
2
2
Replacing Batteries
3
3
Operations
The
CLIKR
TM
-5
UR5U-8780L & UR5U-8790L is
designed to operate the CISCO / SA, Pioneer,
Pace Micro, Samsung and Motorola digital
set tops, Plus the majority of TV, VCR, DVD
and AUX equipment on the market as
shown below.
A. Quick Set-Up Method
STEP1
Turn on the equipment you want to
program. To program your TV, turn on
the TV.
STEP2
Point the remote at the component and
press and hold the [DEVICE] key for 3
seconds until the Device LED blinks off
and turns back on. Continue holding
the [DEVICE] key and press the number
keys, one at a time, starting with 1, then
2, 3...0. Stop pressing the number keys
when the device turns off.
STEP3
Release the [DEVICE] key to save the
code. The Device LED will blink twice
to confirm the code is stored.
Repeat the steps above for all components
(TV, VCR, DVD, AUX).
B. Pre-Programmed 3-Dight Code Method
STEP1
Turn on the equipment that you want
the remote control to operate (Cable
Box, TV, VCR, DVD, etc.).
STEP2
Press the [DEVICE] button and the
[OK/SEL] button simultaneously for
three seconds. The corresponding
device LED will turn on indicating that
it is ready to be programmed. The LED
will remain on for 30 seconds. The
next step must be entered while the
LED is on.
STEP3
Point the remote control toward the
equipment and enter the three-digit
code number assigned to your brand
from the code tables. If there are more
than one three-digit number listed for
your brand, try one code number at a
time until your equipment turns off.
*Note :
You can verify that you have selected the
correct code by pressing the [POWER]
button. The equipment should turn back
on. Then try all of the functions on the
remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any
of the functions do not operate as they
should, repeat the instructions from
STEP 3 above using the next three digit
code number from the brand list.
STEP4
Store the three-digit code by pressing
the same [DEVICE] button once
again. The device LED will blink twice
to confirm that the code has been
stored.
C. Auto-Search Method
If none of the three digit code numbers
assigned to your brand of equipment works, or
the code table does not list your brand, you can
use the Auto Search Method to find the correct
three-digit code number for your equipment by
following steps:
STEP1
Turn on the equipment that you want
the remote control to operate (Cable
Box, TV, VCR, DVD, etc.).
STEP2
Press the [DEVICE] button and the
[OK/SEL] button simultaneously for
three seconds. The device LED will
turn on indicating that it is ready to be
programmed. The LED will remain on
for 30 seconds. The next step must be
entered while the LED is on.
STEP3
Press the [CH
] or [CH
] button one
at a time or keep it pressed. The
remote will emit a series of Power
ON/OFF code signals. Release the
[CH
] or [CH
] button as soon as the
equipment turns off.
*Note :
You can verify that you have selected the
correct code by pressing the [POWER]
button. The equipment should turn back
on. Then try all of the functions on the
remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any of
the functions do not operate as they should,
repeat the instructions from STEP3 above
to continue the Auto Search Method.
STEP4
Press the same [DEVICE] button to
store the code. The Device LED will
blink twice to confirm that the code
has been stored.
D. To Identify the 3-Digit Code
Programmed for a Device
STEP1
Press the appropriate [DEVICE] button
and the [OK/SEL] button simultaneously
for three seconds. The device LED will
turn on for 30 seconds. The next step
must be performed while the LED is on.
STEP2
Press the [INFO] button. The device LED
will blink a number of times indicating
the number of each digit for the code.
Each digit is separated by a one second
interval of the LED being off.
Example :
One blink, (pause) three blinks,
(pause) eight blinks indicates the
code number 138.
*Note :
Ten blinks indicates the number 0.
E. Programming the AUX Device
You can take advantage of the AUX function to
program a devices such as a media PC, gam-
ing console or satellite radio receiver. Follow
the instruction in section B to program an AUX
device. You can also program the AUX button
for a second TV, VCR or DVD player. To do this
follow the instructions below.
STEP1
Turn on the 5th device you want to
program (TV, VCR, DVD, etc.).
STEP2
Press the [AUX] button and the
[OK/SEL] button simultaneously for 3
seconds. The [AUX] device LED will
turn on for 30 seconds.
STEP3
Press the [Device] button For the type of
device you want to setup. Point the
remote control toward the device and
enter the 3-digit code number assigned
to your brand.
*Note :
To program a second TV press TV, etc.
STEP4
When the equipment turns off verify
that you have selected the correct
code by pressing the [POWER] button.
The equipment should turn back on.
Then try all of the functions on the
remote control (i.e. volume, mute, etc.)
to ensure you have the correct code.
If any of the functions do not operate
as they should, enter the next 3-digit
code number from the brand list.
STEP5
Once you have found the correct
3-digit code, save it by pressing the
[AUX] button one more time. The [AUX]
LED light will blink twice to confirm the
code was stored.
F. Programming the System On/Off Button
This allows you to program the System On/Off
button so it can send up to five power On/Off
commands with one button press.
STEP1
Press the [CBL] button.
STEP2
Press the [SYSTEM ON/OFF] button
and the [OK/SEL] button simultaneously
for 3 seconds. The [CBL] button will turn
on for 30 seconds.
STEP3
Press the first [DEVICE] button you want
to store in the [SYSTEM ON/OFF] button
and then press [POWER]. Repeat this for
the other components you want to turn
on/off with the [SYSTEM ON/OFF] button.
STEP4
Press the [CH
] button to save the
power commands you stored. The
[CBL] button will blink twice to confirm
the commands have been saved.
G. Programming Volume Control
Volume and Mute control are factory programmed
to automatically transfer to the respective Device
mode You select, as follows:
CBL
: TV
T V
: TV
VCR
: TV
DVD
: TV
AUX
: AUX
If you wish to store the CBL volume control in
CBL mode, use the following steps.
STEP1
Press the [OK/SEL] button and [CBL]
button simultaneously for three
seconds. The device LED will turn on
for 30 seconds. The next step must
be performed while the LED is on.
STEP2
Press the [VOL
] button. The device
LED will blink.
STEP3
Press [CBL] button. The device LED will
blink twice to confirm the programming.
*Note :
To return CBL device to TV volume
repeat steps above replacing [CBL]
with [TV] in Step 3.
H. Programming Channel Control
You can program the channel controls (Channel
Up, Channel Down, Last and Numbers) from
one Device to operate in another Device mode.
Default channel control settings on the remote
control are as follows:
CBL
: CBL
T V
: CBL
VCR
: CBL
DVD
: DVD
AUX
: AUX
If you wish to store the TV channel controls in
TV mode, use the following steps.
STEP1
Press the [OK/SEL] button and [TV] button
simultaneously for three seconds. The
device LED will turn on for 30 seconds.
The next step must be performed while
the LED is on.
STEP2
Press the [VOL
] button. The device
LED will blink.
STEP3
Press [TV] button. The device LED will
blink twice to confirm the programming.
*Note :
To return TV device to CBL channel
repeat steps above replacing [TV] with
[CBL] in Step 3.
I. Programming a ‘Macro’ button.
If your remote model has custom-programmable
Macro buttons available(See Section 4), they
can be programmed to act as a ‘Macro’ or
Favorite Channel button in CABLE mode. This
allows you to program up to five 2-digit channels,
four 3-digit channels or three 4-digit channels
that can be accessed with one button press.
STEP1
Press the [CBL] button to select the CBL
mode.
STEP2
Press the [MACRO] button and
[OK/SEL] button simultaneously for 3
seconds. The [CBL] button will turn
on for 30 seconds.
STEP3
Enter the the 2, 3 or 4-digit code for the
channel you want programmed first (for
example, 007) using the Number Pad,
then press the [STOP] button. Then
enter the code for the next channel (for
example, 050), then press the [STOP]
button. Repeat this process for the third
channel. The [CBL] button will blink
once for each channel entered.
STEP4
Press the [CH
] button to store the
channels that were selected. The
[CBL] button will blink twice to confirm
the storage of commands.
To access the programmed channels, press
the [MACRO] button once. This will bring up
the first channel. Press once again and it will
bring up the second channel. Press again and
it will bring up the third channel.
J. Low Battery Warning
When the batteries are low and need to be
replaced with fresh batteries, the Device LED
lights will blink 2 times in sequence whenever a
[POWER] button is pressed to turn on equipment.
K. Memory Lock System
This remote control is designed to retain pro-
grammed memory for 10 years even after bat-
teries are removed from the remote control.
L. Record Your Component Set-up Codes
TV
Set-up Code Number:
VCR Set-up Code Number:
DVD Set-up Code Number:
AUX Set-up Code Number:
For additional information about your remote
control, go to www.universalremote.com
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1
Remove the battery compartment cover
on the back of your remote control.
STEP2
Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3
Replace the battery compartment cover.
CBL
: Cable Set-top Box
TV
: Televisions
VCR
: VCRs and TV/VCRs
DVD
: DVD Players
AUX
: Audio Equipment, Media PC, etc.
6
6
Quick Set-up Code Tables
TV
Quick Number
Manufacturer/Brand
0
SANYO
1
SONY
2
SAMSUNG
3
LG
4
TOSHIBA
5
PANASONIC
6
PHILIPS
7
HITACHI
8
SHARP
9
VIZIO
VCR
Quick Number
Manufacturer/Brand
0
MITSUBISHI
1
HP
2
PHILIPS
3
JVC
4
SAMSUNG
5
PANASONIC
6
PHILIPS MAGNAVOX
7
TOSHIBA
8
PIONEER
9
LG
DVD
Quick Number
Manufacturer/Brand
0
HITACHI
1
SONY
2
PHILIPS
3
SAMSUNG
4
PHILIPS MAGNAVOX
5
PANASONIC
6
LG
7
JVC
8
DENON
9
PIONEER
AUX
Quick Number
Manufacturer/Brand
0
BOSE
1
HP
2
APPLE / iPod
3
APPLE / iPod
4
MICROSOFT / XBOX
5
SONY / PS2
6
LUTRON
7
X-10
8
ZINWELL
9
MICROSOFT / XBOX
CBL-CABLE Converters
Manufacturer/Brand
Set-Up Code Number
TV
Manufacturer/Brand
Set-Up Code Number
GENERAL INSTRUMENT 005 103 104
HAMLIN
049 050 055
HITACHI
103 055
JERROLD
005 004 103 005 003 008 009 010 069
MAGNAVOX
010 012
MEMOREX
052
MOXI
111 252 153
NFUSION
192
PANASONIC
044 047
PHILIPS
006 012 013 020 085
PULSAR
052
RCA
047
REGAL
049 050
REGENCY
057
SKY
230 204
SONY
108
SPRUCER
047
TELNET
354
TOCOM
039 040 056
TOSHIBA
052
VIEWSTAR
012 015
ZENITH
052 060 093 100
A MARK
112 143
ABEX
025
ACCURIAN
036
ADMIRAL
072 251 333
ADVENT
247 388
ADVENTURA
002
AIKO
103
AKAI
116 146 248 404 405 473 475 323 387 391 615
ALBATRON
017
ALERON
028
AMERICA ACTION
043
AMPRO
073
AMSTRAD
052
ANAM
043 054 056 080 112
AOC
116 363 112 058 616
APEX
572
APEX DIGITAL
006
AQUAVISION
573 574
ASTAR
477
AUDIOVOX
076 454 388
AVENTURA
052
AVION
441
AXION
039
BELCOR
116
BELL&HOWELL
333 072
BENQ
423 600
BOXLIGHT
266
BRADFORD
043
BROCKWOOD
116
BROKSONIC
238
BYDESIGN
031 032
CANDLE
116 002 003 363
CAPEHART
058
CARY AUDIO DESIGN
266
CELEBRITY
001
CENTURION
116
CETRONIC
043
CHANGHONG
247
CITIZEN
116 002 003 363 043 258 103 143
CLARION
043
CLASSIC
043
CLP CLASSIC
333
COLORTYME
116
CONCERTO
363
CONCIERGE
073
CONTEC
043 050 051
CORNEA
116
CORONADO 143
CRAIG
043 054
CROSLEY
164
CROWN
043 143
CURTIS MATHES 116 258 363 143
CXC
043
CYBERHOME
015
DAEWOO
363 016 043 044 076 103 114 125 127 143
DAYTRON
363 143
DELL
320 164 363 618
DIGITAL PROJECTION
570
DIMENSIA
333
DREAMVISION
235
DUKANE
011 025
DUMONT
116 073
DURABRAND
096 052
DWIN
257
DYNASTY
043
DYNEX
400
EIKI
187
ELECTROBAND
001
ELECTROGRAPH
466
ELECTROHOME 143 024 076 196
ELEKTRA
072
ELEMENT
363 494 526
EMERSON
028 048 043 155 005 116 363 047 050 051 076 096
143 153 154 052 514
ENVISION
116
EPSON
324 590
ESA
323
FISHER
007 057
FUJITSU
246 198 410
FUNAI
028 043 052
FUTURETECH 043
GATEWAY
242 268
GE
073 116 008 009 034 056 074 155 333 363
GEM
391
GIBRALTER
116 073
GO VIDEO
026
GOLDSTAR
113 116 102 363 106 112 127 143
GRUNPY
028 043
HAIER
363 501
HALL MARK 363
HANNSPREE
349 381
HARLEY DAVIDSON
028
HARVARD
043
HAVERMY
081
HELLO KITTY
076
HIMITSU
043
HISENSE
419 442
HITACHI
011 166 009 010 012 023 075 143 158 072 363 250
587 613
HP
378 316 327 421
HUMAX
518
HYPERION
609
HYUNDAI
337 338
ILO
472 399
INFINITY
164
INFOCUS
333 230 547 548 470 532 564 595
INITIAL
035 282
INSIGNIA
350 400 052 164 403 454 457 604 617
INTEQ
073
JANEIL
002
JBL
164
JCB
001
JCPENNEY
024 116 008 009 030 065 258 143 333 363
JENSEN
013
JVC
038 034 001 083 199 210 533 581
KAWASHO
116 001
KEC
043
KENWOOD 116 001
KLEGG
466
KLOSS
002 059
KMC
143
KNOLL SYSTEMS
230
KONKA
457
KREISEN
530
UR5U-8780L & UR5U-8790L
DEFAULT STATE:
Device Default:
Cable Set-Top Box (STB)
Channel Default:
CABLE channel and numbers
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers
through the TV or VCR. Refer to section
H
for
programming steps.
Volume Default:
Volume and Mute control are
automatically transferred to the respective
Component based on the Device selected:
CBL
:TV ;
TV
:TV ;
VCR
:TV.
DVD
:TV ;
AUX
:AUX.
You have the option of controlling CABLE
Volume and Mute through the TV, VCR or
AUX. Refer to section
G
for programming
steps.
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, VCR,
DVD or AUX button, depending on what device you are programming the remote to operate.
There are three ways you can program your remote:
* Quick Set-Up Method
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
This is the quickest way to set up devices made by popular manufacturers.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
backside of the operating instructions.
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
identify the correct code.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
7
7
Set-up Code Tables
CBL-CABLE Converters
Manufacturer/Brand
Set-Up Code Number
Manufacturer/Brand
Set-Up Code Number
TV
SCIENTIFIC ATLANTA 001 003 041 042 045 046
PIONEER
001 103 034 051 063 076 105
PACE
001 005 002
SAMSUNG
001 030
MOTOROLA
002 111 148
CE-LABS
164
DIGEO
153
EVOLUTION FTA
158
