background image

Contents

Letter of certifi cation  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  2

Scope, certifi cation, and installer responsibility .  .  .  .  .  .  .  .  3

Warranty  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3

SunFrame components  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4

Installer supplied materials  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4

Planning code-compliant SunFrame installations .  .  .  .  .  .  .  5

Installing the array  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  8

Footing and splicing requirements  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  9

Material planning for rails and cap strips   .  .  .  .  .  .  .  .  .  .  11

Frequently asked questions
about standoffs and roof variations  .  .  .  .  .  .  .  .  .  .  .  .  .  .  12

October 2003

Pub 031016-2ii

©2003 by UniRac, Inc.

All rights reserved.

Code-Compliant Planning and Assembly

with California Building Code Certifi cation*

Installation Manual 802

SunFrame™ products are U.S. patent pending.

*For Uniform Building Code certifi cation for SunFrame, see Installation Manual 801.1.

Summary of Contents for SUNFRAME - INSTALLATION 802













Reviews: