![background image](http://html.mh-extra.com/html/uncle-milton/disney-princess-sparkle-light-projector/disney-princess-sparkle-light-projector_manual_838230001.webp)
TM
Installing batteries into Light Projector
Tool required - Small Phillips head screwdriver
1. Use a Phillips head screwdriver to remove the battery cover.
2. Insert 3 “AAA” batteries. Make sure the “+” and “-” ends are
inserted correctly, as indicated in the battery compartment.
3. Replace cover.
Using Sparkle Light Projector
IMPORTANT: Before operating, be sure on/off switch located on the
back of Light Projector is turned to the “ON” position.
The Light Projector will shut off when the button is pressed 1.5
seconds in any mode.
NOTE: Carefully lower dome onto the Light Projector base and snap
into position. The dome should sit firmly on top of base.
Color Mode
There are 7 different light modes. Each time you press the mode
button it will advance to the next light mode. If you leave the
projector on a mode, it will automatically turn off after 20 minutes.
5+
2363
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD
Questions? Visit us at unclemilton.com
2363-0250-0316-v01
Batteries not included
Requires 3
x 1.5V AAA/LR03
batteries
x3
AAA/LR03
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
In an environment with electrostatic discharge, the product may malfunction.
In this case, remove the batteries and wait for 5 minutes and then replace the batteries.
BATTERY SAFETY INFORMATION
• Only adults should install and replace batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Do not dispose of batteries in fire. Battery may explode or leak.
• Batteries should be recycled or disposed of as per state and local guidelines.
MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.
P.O. Box 6281, THOUSAND OAKS, CA 91359 USA
©2016 UMI. All rights reserved. ® and TM designate trademarks
of Uncle Milton Industries, Inc.
MADE IN CHINA
This product and its batteries must be
disposed of separately at your local
waste recycling centre. Do not dispose
them in your household waste bin.
Mode button
©Disney
Visit disney.com
Sparkle
Light Projector
The Light Projector will remember the mode last used.
MODE
INITIALLED ON
LIGHT EFFECT
1
White
White
2
Pink
Pink
3
White
White fast fade
4
Pink
Pink fast fade
5
Pink
Random pink/white fast fade
6
Pink
Random pink/white slow fade
7
All
Pink/white fade
8
Off