#CF4 - 4ft. Lightweight Electric Camp Fence
Bear Shock
Contents
Thank you for purchasing
Bear Shock
electric fence! Please read the
following instructions carefully to become acquainted with some of the
important features of your new lightweight electric fence. This high-
performance device must be installed and operated properly in order to
achieve the best possible results.
Bear Shock
is designed to provide safety and sound sleep while in bear
country and to help protect you and your equipment from curious bears
by providing a surprising electrical shock when touched.
UDAP Industries, Inc. has proudly produced one of the finest, highest-
quality battery-operated lightweight electric fence systems available.
Two D-cell batteries (not included) power the Bear Shock fence
energizer. Because of the efficient electronic circuit design, two alkaline
D-cells will last approximately 5 weeks under continuous operation,
depending on fence and weather conditions.
Bear Shock
is fully adjustable and can easily adapt to most
environments. There is enough poly wire to fence an area 27 ft by 27 ft.
A much smaller/larger area can be fenced by cutting/tying the poly
wire. If cut, the poly wire can later be tied back together if a larger area
is preferred.
This electric fencing system presents a mental barrier to an animal
rather than a physical barrier. Once an animal is shocked, even though it
has not been harmed, it will respect the fence out of fear of being
shocked again.
Caution
Bear Shock
does not
replace
recommended
safety measures. Never
store food or odorous
items in or near your
sleeping
area.
For
recommended
procedures for camping
in bear country, refer to
the Bear Safety Tips
Booklet provided. For
additional safety in bear
country have
UDAP
Pepper Power Bear Spray.
Assembly Directions
1
Pole and wire assembly
1.
Each corner pole will need to be assembled. Included
with this product are 24 pole insulator clips. Install
three clips on each corner pole by twisting the clip
clockwise onto the pole. Be sure that the open end of
the clip is facing up. The portion of the corner pole
with the metal insert is the bottom piece. Install one
clip in the middle of the bottom section of the corner
pole. Install one clip just above the metal insert of the
top pole and then install the third clip a couple inches
from the top of the corner pole. (See Picture)
2.
After corner poles are assembled place at the 4 - 8
corners of your site. Depending on how many posts
needed.
3.
Push each corner pole into the ground at a 30-
degree outward angle deep enough to keep them
stable. Rocks or other material may be used as
braces stacked around poles if poles fail to stay in
ground.
NOTE: The poly wire requires some pre-assembly. This is a
one-time assembly process and does not need to be done
again. Please read “Poly Wire Initial Assembly Directions”
before continuing for the first time.
2
Poly Wire Initial Assembly
1.
The spool of poly wire comes in three equal lengths of 110
feet each.
2.
At one end of
each wire tie a
small loop (See Picture). Once the
loop is tied you may run the poly
wire around your fence.
3.
At the other end of the poly
wire complete the below
assembly.
4.
Included in the Bear Shock kit
is three metal Snap Hooks and
three plastic Line Tighteners.
The Line Tightener is the small plastic piece with three holes
(See Picture).
UDAP Industries Inc.
P.O. Box 4872
Butte MT, 59702
Phone: 406-494-9292
Fax: 406-494-9797
Email:
Pepper
Power
@udap.com
Pepper
Power.com
Part
Qty
A.
UDAP Bear Safety Tips Booklet
1 ea.
B.
Hot wire
1 ea.
C.
Ground wire
1 ea.
D.
Flagging tape
1 roll
E.
Energizer
1 ea.
F.
Poly wire line tightner and snap hook
3 ea.
G.
3 Electrical poly wires (180’ ea.) spooled
1 ea.
H.
4 foot Plastic-coated support poles (top and bottom)
with a total of 3 black insulators clips attached to each
assembled pole
8 ea.
I.
Ground stake
1 ea.
J.
Storage bag
1 ea.
