TurboChef SOTA NGO Service Manual Download

Page: 1 / 85

turbochef technologies, inc.

ngo rev e service Manual changes

May 2010



Upper jetplate part number now i1-3204



Added i1-9179 support rails to appendix



Added NGC-1194 switch offset shim (x2)



i1-9029 (SOTA) / i1-9023 (NGO)



SOTA letters: i1-9052 = S, i1-9053 = O,

i1-9054 = T, i1-9055 = A, i1-9056 = Caret



Left ctl: i1-9057 (SOTA) / i1-9453 (SBK)



Right ctl: i1-9058 (SOTA) / i1-9452 (SBK)



Door cover: i1-9109 (SOTA) / i1-9444 (SBK)



Shell: i1-9240 (SOTA) / i1-9445 (SBK)



Medallion: i1-9491 (SOTA) / i1-9489 (SBK)



LED light ring: i1-9198



Front panel: i1-9246 (SOTA) / i1-9458 (SBK)



Keypad: i1-9451-1 (SOTA) / i1-9451-2 (SBK)



i1-3201 = NGO SBK Door Kit



Added LED light ring to “controls” section



Specified “gray” smart card



Various appendix drawing updates



Add to safety instrutions: DO NOT cook with

metal lids or aluminum foil



Add to safety instrutions: DO NOT cook

without food in the cook cavity



Specified i1-3202 waveguide kit



Specified i1-3207 switch paddle kit



Removed blower component (hub, wheel, heat

slinger) part numbers, changed to REF



Appendix housekeeping



Updated door detail and part numbers



Removed blower assembly detail



Specified stirrer blade kit i1-3208



Changed coupling part number from 104134

to 104306



Updated stirrer motor detail



Changed motor controller part number from

100446 to CON-7039



Added international component part numbers



Added i1-3210 shunt plate kit



Added note about how to apply a new keypad



Added note to not apply push nut to trim

prong, to prevent interference with display



Added section: Troubleshooting: Menu settings

are not present



Moved “Write fail” troubleshooting to page 42



Updated schematic



Specified NGC-3033 for primary switch

replacement and modified drawing



Added notes for replacing primary switch



Specified stirrer shaft kit i1-3209



Added verbiage to cleaning instructions about

not forcing the rack out by pulling upward

Summary of Contents for SOTA NGO






















































































Search results

Summary of Contents for SOTA NGO

Reviews:

Related manuals for SOTA NGO

Brands by name

Popular brands

TurboChef SOTA NGO, Service Manual

Search results

Summary of Contents for SOTA NGO

Reviews:

Related manuals for SOTA NGO

Brands by name

Popular brands