ECE 44.04
Approved
for Group 2 & 3
4 - 12 yrs / 15 - 36 kg
User Guide
When used in accordance with these instructions the booster cushion
allows an approved adult seat belt to be used by a person of small
stature.
All product information, video instructions and BoostApak extras are
available from BoostApak.com
Product Care
To remove fabric first undo Velcro strips in front of seat belt guides
(Fig a). Then unzip the internal zipper in the lining (Fig b) to peel fabric
away from plastic shell, starting from the corners (Fig c).
Follow the wash care label attached for advice on cleaning the
BoostApak fabric. Never use bleach, dye, or chemical cleaners. Only
sponge clean the BoostApak fabric, using hand soap and warm
water.
Notice
This is a “Universal” child restraint. It is approved to Regulation No.
44,04 series of amendments, for general use in vehicles and it will fit
most, but not all, car seats.
A correct fit is likely if the vehicle manufacturer has declared in the
vehicle handbook that the vehicle is capable of accepting a
“Universal” child restraint for this age group.
This child restraint has been classified as “Universal” under more
stringent conditions than those which applied to earlier designs
which do not carry this notice.
If in doubt, consult either the child restraint manufacturer or the
retailer.
boostapak.com
ECE 44.
for G
4
- 12
1
2
2
5
6
Installation
Follow installation instructions closely as an incorrect installation could be dangerous.
IMPORTANT - This booster seat is only suitable for use in vehicles fitted with 3 point retrac-
tor safety belts approved to ECE Regulation No. 16 or other equivalent standards.
Place the BoostApak forward facing on the vehicle seat (see installation diagram on the
BoostApak seat).
1.
Lift up the front to reveal green armrests.
2.
Lift green armrests until
they lock into an upright position.
3.
Attach the shoulder clip link strap to the D-ring,
located at the rear of the BoostApak, on the same side as the vehicle buckle.
4
. Ensure clip
is at the correct height for the user. Pull the clip directly upwards from the ‘d’ loop, the
marker beneath the Trunki logo should be shoulder height.
5.
When length is set, swing the
clip to the opposite shoulder and fix behind the user to the diagonal section of the seat belt.
6.
Place child on BoostApak and pass the seat belt lap portion over their lap ensuring the
belt is over the red sticker on each side of the Boostapak. Engage the buckle and ensure
the diagonal belt is over the red sticker on the arm rest, across the chest and over the
shoulder. Ensure the diagonal belt engages with the
shoulder strap clip. When using the BoostApak outside the
vehicle the green armrests can be lowered by pressing the
buttons on the side.
Warnings
1.
DO NOT use in any configuration not shown in the
instructions.
2.
DO NOT use any load bearing contact
points other than those described in the instructions and
marked on the BoostApak.
3.
DO NOT use the BoostApak
in any seating position where an airbag is present, unless
the airbag can be switched off.
4.
IMPORTANT - Ensure
that the vehicle seat belts are not twisted and that the lap
strap is worn low down, so that the pelvis is firmly engaged.
5.
DO NOT make any alterations or additions to this product without approval of the manufacturer.
Only use fabric as recommended by the manufacturer, other fabrics could reduce the performance. Check the fabric cover from time to time to ensure it is not
damaged or torn in any way and that the zip is in good order. If any damage is detected or the zip does not function, contact the manufacturer immediately for
a replacement fabric. Do not use the product unless the fabric is in good order.
6.
DO NOT use the BoostApak if it is damaged or has been subject to any violent
stresses of an accident.
7.
DO NOT use an ordinary loose cushion to substitute or use with the booster seat.
8.
IMPORTANT - Secure luggage or objects liable
to cause injuries in the event of an accident.
9.
IMPORTANT - All rigid items and plastic parts of the child restraint
must be located and installed so that they are not likely, during everyday use of the vehicle, to become trapped by
a movable seat or in a door of the vehicle.
10.
IMPORTANT - Ensure the BoostApak is not overfilled such that the
back becomes distorted (Fig d & e).
11.
IMPORTANT - Max weight of BoostApak and its contents should not
exceed 15% of the childs weight.
12.
DO NOT leave a child in the child restraint system unattended.
13.
The
booster must only be used in vehicle seating positions indicated and facing in the direction of travel (forward).
Please refer to the vehicle owners manual to clarify the suitability of other seating positions which may not be
indicated.
14.
The plastic parts of the BoostApak may become hot if left in direct sunlight. Please avoid contact with
the child's skin.
b
c
a
d
e
