SELF CONTAINED LED EMERGENCY
Model: ESCAPE LED AT
Self-contained emergency equipped with LED lamp 1*3W (CREE) with special wide angle lens and constant current control, ideal for
installation in escape routes.
The luminary is designed to work in Maintained & Non Maintained mode depending on the connection and has a small green LED which
indicates the power presence and battery charging.
Characteristics:
-
Supply 230 V 50/60Hz.
-
Input current: 40mA (Maintained mode).
-
Maintained/Non Maintained.
-
Automatic TEST function (Self –test).
-
Tri-color LED (green/red/yellow) to indicate the different stages of the luminary.
-
Output voltage: 3VDC/Output current: 600mA (constant current control)/Output power: 1.8W.
-
Autonomy superior 1 or 3 hours.
-
Protection against Overloading and end of Battery Discharge.
-
Color Temperature 6000-6500K/Lumens: 150Lm.
-
Grade IP20/Class II device / Ambient temperature: 0-50ºC.
-
Standby-restart and manual control of AUTO TEST function via Telemando TM.
-
Battery charging 24 hours.
-
Max cross section of cable to be connected 1,5mm.
-
Recessed mounting.
-
CE marked as per directives 2006/95/CE and 2004/108CE EMC.
-
Manufactured in accordance to norms UNE-EN 60598-2-22UNE-EN 61347-2-13.
SELFTEST Function
The Emergency Luminary has a programmed micro controller to execute automatically or manually a series of verification TESTS, to verify
the working of the Luminary.
Basically these TESTS do the verification of the two of the most important elements of the Luminary:
1. Emergency Lamp (3W LED): Runs an Automatic TEST WEEKLY during 15 seconds.
2. Battery (Autonomy): Runs an Automatic TEST of 1 hour duration, every 26 weeks.
*uses an internal clock for the timings and it is not as perfect as a profession calendar clock.
SELF TEST programming:
Once the Luminary is connected to the Power for the 1
st
time, the dates for AUTOMATIC TESTS are set. It runs a Verification TEST of LED
LAMP weekly and a verification TEST of the BATTERY every 26 weeks.
In a situation, when there is a POWER failure coinciding with the execution of the Programmed BATTERY TEST, the TEST is postponed
and is executed when NEXT LAMP TEST is programmed. If during a TEST there is a power failure, the TEST will continue till the end. The
battery TEST can be cancelled by pressing the TEST button for more than 6 seconds.
The TEST results are indicated by Green & Red LED and are memorized until performing RESET.
RESET:
On doing the RESET all the Timings and Alarms are RESTARTED. To perform the RESET, disconnect the battery connector, wait approx.
10 seconds and connect the battery. All memorized FAULTS are deleted only if the indicated fault is solved, if the cause of the fault is
battery, then the next battery test will be programmed within 1 week to check the correct autonomy of the battery.
Manual TESTS:
The LAMP and battery TESTS can also be done manually by using TELEMANDO TM (pressing ON).
LAMP TEST: To execute the LAMP TEST manually, Press the TELEMANDO TM ON button during 3 to 6 seconds.
BATTERY TEST: To execute the BATTERY TEST manually, Press TELEMANDO TM ON button for more than 6 seconds
On executing the manual test all the times are RESET (lamp test every week & battery test every 26 weeks from the date of execution of
manual test). During the 1st 24 hours or after prolonged power failure it only allows to do the lamp TEST and not the battery test.
Standby-restart (Emergency mode)
In emergency mode it is possible to switch off and ON the luminary to save battery power, to do this press the ON button of TELEMANDO
more than 6 secs. Telemando can be connected to several luminaries (see connection diagram)
Test results & different situation Indications:
1.
Luminary OK: GREEN Led ON or blinking during 1
st
24 hours of installation.
2.
Lamp Failure: RED led blinking.
3.
Electronic driver failure: YELLOW led blinking.
4.
Battery Failure (Autonomy): RED Led ON.
5.
Power Failure or Voltage below 170 Volts: RED and GREEN Led OFF.
6.
Lamp test in progress: GREEN Led blinking (1 short blink).
7.
Battery test in progress: GREEN Led blinking (2 short blinks
).
8.
On executing the manual test (via telemando): GREEN/RED led illuminate alternatively.
Installation:
- Make a hole of 57 mm diameter in the ceiling to introduce the driver and the battery and recess the luminary once connected. (refer to the
connection diagrams on next page for connection and follow the following steps)
- Switch OFF the power to make the installation.
- Make connections to the connector (N,L), this line should be permanent, as it is charging the battery permanently and if the line is cut the
luminary will enter in emergency mode.
- Make connection to connector (L1) (see Maintained mode connection diagram), It is also possible to connect a switch in this line to switch
ON/OFF the in maintained mode (see connection diagram)
- Connect the 3*1W LED lamp wire to the driver connector (LED LAMP + -) respecting the polarity indicated (red+/black-)
- Connect the green LED wire to the driver connector (battery charging indicator), respecting the polarity, the special connector enables the
possibility of connection error.
- Connect the battery to the driver verifying the correct polarity. It is advisable to maintain a distance with LED lamp.
-Introduce the driver and battery through the ceiling hole, and recess the luminary in the ceiling, Switch ON the power and verify that the
Green LED indicating the battery charging and 3*1W LED lamp ( in permanent mode) is ON.
IMPORTANT: Do not disconnect the LED lamp from the driver in working mode.
Maintenance:
The manipulation and the installation of the kit should be done by qualified technicians.
Always verify that the Voltage of the Mains is adequate to the input voltage of Luminary.
Before installation make sure the mains is OFF and the battery is disconnected.
F
IP20
Lighting Technologies TRQ, S. L. U.
