Tripp Lite SmartRack SR42UBEIS Owner'S Manual Download

Page: 1 / 13

SmartRack

Rack Enclosure

with IP54 (NEMA 12) Rating

Model: SR42UBEIS

Owner’s Manual

Important Safety Instructions

Overview 2
Feature Identification

Enclosure Installation

Preparation

Unpacking

Placement

Leveling

Ground Connection

AC Power Connection

Enclosure Configuration

Adding or Removing Front and Rear Doors

Adding or Removing Roof Panel

Adding or Removing Side Panels

Adjusting Mounting Rails and

Cable Management Rails

Combining (Baying) Enclosures

Cleaning/Replacing Filters

Installing the Cable Access Housing (Optional) 10

Equipment Installation

Installing or Removing Cage Nuts

Specifications 12
Storage and Service

Warranty and Product Registration

Español 13
Français 25

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

Summary of Contents for SmartRack SR42UBEIS














Search results

Summary of Contents for SmartRack SR42UBEIS

Reviews:

Related manuals for SmartRack SR42UBEIS

Brands by name

Popular brands

Tripp Lite SmartRack SR42UBEIS, Owner'S Manual

Search results

Summary of Contents for SmartRack SR42UBEIS

Reviews:

Related manuals for SmartRack SR42UBEIS

Brands by name

Popular brands