![background image](http://html.mh-extra.com/html/trilite/sg10-12rg/sg10-12rg_installation-instructions_1162671001.webp)
INSTALLATION INSTRUCTIONS for MODELS
SG10-RG (Incandescent) and SG10-RG-LED
IMPORTANT SAFETY INFORMATION
INSTALLATION INSTRUCTIONS
[email protected] | t: 1-773-384-7765 | f: 1-773-384-5115 | www.triliteinc.com | Designers and manufacturers of specialty electrical products. Since 1922.
953063 | REV B
A1612R
Red signal assembly, 12 VDC
A1612G
Green signal assembly, 12 VDC
A1624RH
Red signal assembly, 24 VAC/VDC
A1624GH
Green signal assembly, 24 VAC/VDC
A16115R
Red signal assembly, 120 VAC
A16115G
Green signal assembly, 120 VAC
LIMITED WARRANTY
This Tri Lite product may incorporate an LED bulb, warranted to be free from defects in materials and/or workmanship for (3) three years from the date of delivery to
Purchaser. The Limited Warranty does not apply to severe applications.
All other components within this unit are under warranty for (1) year. If any component parts do not conform exactly to the specifications and physical dimensions referred
to above, and the Purchaser, at its expense, returns the product or component parts to the Seller together with a report of defects, the Seller shall review the inspection
report and inspect the items and shall authorize, at its option, either the repair or replacement of any non-conforming products or component parts. Upon expiration of
the warranty period, all liability of the Seller shall be terminated.
Seller shall not be liable for any injury, loss or damage, direct or consequential arising out of the use or the ability to use the product. This warranty gives specific legal
rights. You may have other rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so that the
above limitation of exclusion may not apply to you.
CAUTION!
The individual user should determine prior to use whether this device is suitable, adequate,
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer
makes no representation or warranty as to the fit or suitability of these devices for any specific application.
CAUTION!
Ensure that the power supply matches the voltage rating of the light.
CAUTION!
Units with incandescent lamps require a flashing power supply or integrated flasher device to
avoid heat damage to the lens. LED units can operate safely when not flashing.
CAUTION!
12 volt units with LED lamps require careful control of the DC input voltages if generated from
AC power sources. Ensure that voltage does not exceed 110% of rated voltage.
REPLACEMENT PARTS LIST
Part#
Descriptions
SG10 CONFIGURATIONS
SG10-12RG
12v
2.17
Incandescent
SG10-12RG-LED 12 VDC 0.30
LED
SG10-24RG
24v 1.10
Incandescent
SG10-24RG-LED 24v
0.11
LED
SG10-115RG 120v 0.21
Incandescent
SG10-115RG-LED 120v 0.03
LED
Part#
Voltage Amps
Bulb Type
These models are intended for use with external peripheral controls and circuitry provided by the user.
1. Choose a location within convenient distance to a suitable power source. The power connection can be
through the underside of the housing or through the back plate. Use the ½” EMT fitting provided.
2. Using the housing as a template, mark and drill four (4) corner holes in an appropriate mounting location.
If mounting to brick or masonry, size the holes to accept ¼” diameter lag-type fasteners and anchors.
3. Use the back plate gasket provided when mounting unit to the wall.
4. Connect the control/supply wires to an appropriate external switching device.
See wiring diagram for reference.