background image

Read the Installation Manual carefully and be sure that your water heater has been properly 

assembled, installed and maintained. Failure to follow these instructions exactly could result in a 

fire or explosion, serious bodily injury and/or property damage. 

Installation and service must be performed by a qualified plumber, a licensed gas fitter, or a pro-

fessional technician in accordance with all local codes.  

Improper installation and/or operation by an unqualified person will void the warranty.

– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

– WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

If the information in these instructions is not followed exactly, a fire or explosion may result, 

causing property damage, personal injury, or death.

Marquis

User’s Manual 

TWH

18

0 / TWH

18

0LP

Gas Condensing Water Heater

• Natural Gas(NG) – TWH

18

0

• Liquid Propane Gas (LP) – TWH

18

0LP

Model

WARNING

Date: 7/10/15

2015-7 Marquis User

Summary of Contents for Marquis TWH180





























Reviews: