Service Facts
© Trane 2008
PRODUCT SPECIFICATIONS
MODEL
RATED VOLTS/PH/HZ.
RATINGS
1
INDOOR COIL — Type
Rows — F.P.I.
Face Area (sq. ft.)
Tube Size (in.)
Refrigerant Control
Drain Conn. Size (in.)
2
DUCT CONNECTIONS
INDOOR FAN — Type
Diameter-Width (In.)
No. Used
Drive - No. Speeds
CFM vs. in. w.g.
No. Motors — H.P.
Motor Speed R.P.M.
Volts/Ph/Hz
F.L. Amps
FILTER
Vertical Applications
Filter Furnished?
Type Recommended
No.-Size-Thickness
Horizontal Applications
Filter Furnished?
Recommended Size
REFRIGERANT
Ref. Line Connections
Coupling or Conn. Size — in. Gas
Coupling or Conn. Size — in. Liq.
DIMENSIONS
Crated (In.)
Uncrated
WEIGHT
Shipping (Lbs.) / Net (Lbs.)
TEE3C49A-SF-1B
Convertible Variable Speed –
Communicating Air Handlers
2/4TEE3C49A1000A
TEE3C49A-SF-1B
2/4TEE3C49A1000A
200-230/1/60
See O.D. Specifications
Plate Fin
4 — 14.0
6.19
3/8 - Copper
TXV - Non-Bleed
4
3/4 NPT
See Outline Drawing
5
Centrifugal
10 x 10
1
Direct - Serial ECM
See Fan Performance Table
1 — 3/4
Variable
200-230/1/60
6.8
Yes
Low Velocity
1 - 20 X 25 - 1 in.
See Note
6
See Note
3
R-22 R-410A
Brazed Brazed
1-1/8 7/8
3/8 3/8
H x W x D
59-1/2 x 28-1/2 x 23-1/2
57-7/8 x 26 x 21
188 / 173
AIRFLOW ADJUSTMENT
If the airflow needs to be increased or decreased, see
the Airflow Label on the air handler or the Blower Per-
formance table in these Service Facts. Information on
changing the speed of the blower motor for your specific
outdoor model size is in the Blower Performance Table
or User Interface Menu.
Blower speed changes are made with the User Interface
Menu mounted in the control box.
▲
CAUTION
!
RECONNECT ALL GROUNDING DEVICES.
All parts of this product that are capable of conducting
electrical current are grounded. If grounding wires,
screws, straps, clips, nuts, or washers used to com-
plete a path to ground are removed for service, they
must be returned to their original position and prop-
erly fastened.
HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING
WARNING:
IMPORTANT — This document contains a wiring diagram
and service information. This is customer property and is
to remain with this unit. Please return to service information
pack upon completion of work.
▲
WARNING
!
THIS INFORMATION IS INTENDED FOR USE BY INDI-
VIDUALS POSSESSING ADEQUATE BACKGROUNDS
OF ELECTRICAL AND MECHANICAL EXPERIENCE.
ANY ATTEMPT TO REPAIR A CENTRAL AIR CONDI-
TIONING PRODUCT MAY RESULT IN PERSONAL IN-
JURY AND OR PROPERTY DAMAGE. The manufacturer
or seller cannot be responsible for the interpretation of
this information, nor can it assume any liability in con-
nection with its use.
1
These Air Handlers are A.R.I. certified with various Split System Air Condi-
tioners and Heat Pumps (ARI STANDARD 210/240). Refer to the Split Sys-
tem Outdoor Unit Product Data Guides for performance data.
2
3/4" Male Plastic Pipe (Ref.: ASTM 1785-76)
3
Minimum filter size for horizontal applications will be based on airflow selec-
tion and will be calculated as follows:
Low Velocity Filter: Face area (Sq. Ft.) = CFM / 300
High Velocity Filter: Face area (Sq. Ft.) = CFM / 500
4
Torque Spec for TXV = Tighten 1/6 turn past finger tight
5
See Installer's Guide for drawings
6
For customer ease of filter maintenance, it is recommended that a properly
sized,
remote filter
and grille be installed for horizontal applications. Airflow
should not exceed the face value of the filter being used.
The factory in-
stalled filter should then be removed from the unit.
