background image

KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH Industries, Inc. 
All other trademarks are property of their respective companies. The information in this document is subject to change without notice. 

No company shall be liable for errors contained herein. © 2008-2010 KVH Industries, Inc., All rights reserved. 

54-0361 Rev. C

1

These instructions explain how to install the TracVision C3 on a vessel. Complete instructions 
on how to use the system are provided in the 

User’s Guide

.

Installation Steps

Who Should Install the System?

To ensure a safe and effective installation, KVH recommends that a KVH-authorized technician 
install the system. To find a technician near you, please visi

www.kvh.com/wheretogetservice

.

Linear vs. Circular Systems

The installation process differs, depending on the type of LNB (low noise block) installed in the 
antenna (linear or circular). These differences are noted throughout this guide. In general, North 
American satellites require a circular LNB, while European satellites require a linear LNB.

Technical Support

If you need technical assistance, please contact KVH Technical Support:

1.

Inspect Parts and Get Tools ............ 3

2.

Plan the Installation.......................... 4

3.

Remove the Mounting Plate ........... 5

4.

Remove the Shipping Restraints .... 6

5.

Drill the Mounting Holes ................ 7

6.

Mount the Antenna .......................... 8

7.

Cut Out the Switchplate Hole......... 9

8.

Wire the Antenna ........................... 10

9.

Seal the Cable Access Hole............ 11

10.

Wire the Receiver(s) ....................... 12

11.

Wire the Switchplate...................... 14

12.

Install Service Key(s)...................... 15

13.

Mount the Switchplate................... 16

14.

Install Satellites ............................... 17

15.

Find the Skew Angle...................... 18

16.

Set the Skew Angle......................... 19

17.

Set Up and Test the System........... 20

18.

Educate the Customer.................... 21

N. America, S. America, Australia:

Phone: +1 401 847-3327
E-mail: [email protected]

(Mon.-Fri., 9 am-6 pm ET, -5 GMT)
(Sat., 9 am-2 pm ET, -5 GMT)

Europe, Middle East, Asia:

Phone: +45 45 160 180
E-mail: [email protected]

(Mon.-Fri., 8am-4:30 pm, +1 GMT)

TracVision

®

 

C3 Installation Guide

Summary of Contents for C3

























Reviews: