![background image](http://html1.mh-extra.com/html/toto/neorest-ms990cgr/neorest-ms990cgr_installation-instructions_1140023001.webp)
NEOREST Installation Instructions <Bowl>
The installation of the toilet bowl for the NEOREST differs from installation of conventional toilet bowls.
Be sure to read the following installation instructions and install the product only as described in this manual.
Always Follow This Precaution
1
Avoid direct impact to the ceramic components as this will break the
ceramic and could result in injury or property damage due to water
leakage.
Always use the provided or designated parts for the installation
process.
2003.7
H06658
Parts Included in the Installation Kit
2
✲
Before installation, confirm that the parts listed below are included in the kit.
Before installing the NEOREST, be sure to read the safety instructions
in “Always Follow This Precaution” and install the product only as
described in the instructions.
4
Precautionary symbols are used in these instructions to
ensure safe and proper installation of the product and to
prevent injury to the end-user and damage to personal
property. The definitions of these precautionary symbols
are as follows.
4
There are two types of precautionary symbols.
The symbols and definitions appear below.
Symbol
Definition
WARNING
When this symbol appears,
precaution should be taken to
ensure proper and safe use of
the product. Ignoring this
precaution could result in injury
or damage to personal property.
The
3
symbol indicates a prohibited
use of the product.
This symbol means “Always follow
this precaution”.
WARNING
Part Name
Quantity
Drawing
Toilet
1 unit
1
2
4
4
4
2
2
2
2
2
1
1
1
Outlet connection
Mounting Blocks
Mounting Pieces
Bag of screws
1
Bag of screws
3
Bag of screws
2
Installation Hardw
are
Pan head screws
Self- tapping screws
(for Mounting Blocks)
Self- tapping screws
(for outlet connection)
Bolts
Washers
Washers
Gasket
Paper installation template
Water shutoff valve
Screw caps
Installation instructions
Before Installing the NEOREST
3
■
Confirm that there is enough floor space to install the toilet unit and that the bathroom
door will open/close without obstruction.
■
Confirm that the position of the drain hole and pipes are properly lined up as
designated in the drawing.
■
Water Pressure.
The NEOREST is designed to operate under a minimum working pressure of 10 psi
flowing (as detected by a sensor within the unit). It should be noted that the standard
range of working pressures allowed by model codes is 20 to 80 psi static.*
It is necessary to install the water supply valve (angle stop) provided with the NEOREST.
This will assure the proper flow rate is achieved and allow for optimum performance of the unit.
*See warranty for details.
The following water volume will ensure
sufficient water pressure.
If a pressure gauge is unavailable, the fill method
may be used as follows.
Water volume (for 10 sec)
1.5 Gallons (5.5 L) or more
How to check the water pressure:
(Measuring Procedure)
Allow the water to
flow into the bucket
for 10 seconds and
measure the water volume.
Prepare two buckets to
hold the water.
Line designating the center of the
toilet bowl
Closet flange
Drain R1/2
11
3
/
4
”
(300mm)
5
7
/
8
” (150mm)
12” (305mm)
Installation position
12” (305mm)
Drain pipe installation position
5
7
/
8
” (150mm)
Bathroom
door
At least 1 foot (325mm)
11
3
/
4
”
(300mm)
5
7
/
8
” (150mm)
17
5
/
32
”
(436mm)
32
7
/
8
” (835mm)
NEOREST water supply valve
fully open condition
Optional:
NEOREST water
supply valve fully
open condition
Summary of Contents for NEOREST MS990CGR
Page 4: ......