background image

Form No. 3448-981 Rev A

21in Super Recycler

®

Lawn Mower

Model No. 21565—Serial No. 400000000 and Up

Operator's Manual

Introduction

This rotary-blade, walk-behind lawn mower is intended
to be used by residential homeowners. It is designed
primarily for cutting grass on well-maintained lawns on
residential properties. Using this product for purposes
other than its intended use could prove dangerous to
you and bystanders.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit www.Toro.com for more information, including
safety tips, training materials, accessory information,
help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the product model and serial
numbers in the space provided.

Important:

With your mobile device, you can

scan the QR code on the serial number decal (if
equipped) to access warranty, parts, and other
product information

g374150

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Be sure to register your machine at
www.Toro.com/register. Registration ensures
that you are notified should there be a product recall.
Your registration information is never sold or shared
with third party companies. To avoid waste and
help the environment, a discharge chute does not
come with your purchase (most customers prefer to
recycle or bag their grass clippings). You can request
a discharge chute when you register your product
at www.Toro.com/register. Simply check the box in
the online registration form and Toro will send you a
discharge chute at no additional charge. Please allow
1 to 2 weeks for delivery.

It is a violation of California Public Resource Code
Section 4442 or 4443 to use or operate the engine on
any forest-covered, brush-covered, or grass-covered
land unless the engine is equipped with a spark
arrester, as defined in Section 4442, maintained in
effective working order or the engine is constructed,
equipped, and maintained for the prevention of fire.

The enclosed engine owner's manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance,
and warranty. Replacements may be ordered through
the engine manufacturer.

Gross or Net Torque:

The gross or net torque

of this engine was laboratory rated by the engine
manufacturer in accordance with the Society of
Automotive Engineers (SAE) J1940 or J2723. As
configured to meet safety, emission, and operating
requirements, the actual engine torque on this class
of mower will be significantly lower. Please refer to

© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in Mexico

All Rights Reserved

*3448-981*

 

Summary of Contents for Super Recycler 21565





























Reviews: