Toa C-CV454R-3 CU Instruction Manual Download

Page: 1 / 16

Thank you for purchasing TOA Outdoor Day/Night IR Camera.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

Outdoor Day/Night IR Camera

C-CV454R-3 CU

INSTRUCTION MANUAL

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS

..................................

2. HANDLING PRECAUTIONS

............................

3. GENERAL DESCRIPTION

................................

4. FEATURES

............................................................

5. NOMENCLATURE

..............................................

6. INSTALLATION AND CONNECTIONS

......

7. ADJUSTMENT

......................................................

8. ABOUT MODE SETTING SWITCH

8.1. Focus adjustment switch

........................

8.2. Backlight compensation switch

............

8.3. Flickerless switch

......................................

8.4. ATW/AWB selection switch

....................

8.5. High sensitivity switch

..............................

8.6. Average/Peak selection switch

............

9. TROUBLESHOOTING

....................................

10. SPECIFICATIONS

............................................

Accessories

..........................................................

Summary of Contents for C-CV454R-3 CU

















Search results

Summary of Contents for C-CV454R-3 CU

Reviews:

Related manuals for C-CV454R-3 CU

Brands by name

Popular brands

Toa C-CV454R-3 CU, Instruction Manual

Search results

Summary of Contents for C-CV454R-3 CU

Reviews:

Related manuals for C-CV454R-3 CU

Brands by name

Popular brands