background image

Copyright © 2004, Tjernlund Products, Inc.  All rights reserved.

P/N 8504114

REV.   02/04

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED, LICENSED
SERVICE PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND
OPERATION OF THIS UNIT.  READ THESE INSTRUCTIONS THOROUGHLY
BEFORE ATTEMPTING INSTALLATION OR OPERATION.  FAILURE TO FOLLOW
THESE INSTRUCTIONS MAY RESULT IN IMPROPER INSTALLATION,  ADJUST-
MENT, SERVICE OR MAINTENANCE POSSIBLY RESULTING IN FIRE, ELECTRI-
CAL SHOCK, CARBON MONOXIDE POISONING, EXPLOSION, PERSONAL
INJURY OR PROPERTY DAMAGE.

DO NOT DESTROY.  PLEASE READ CAREFULLY AND KEEP IN

A SAFE PLACE ON JOB SITE FOR FUTURE REFERENCE.

MODELS

VSUB8

VSUB12

VSUB16

VSUB20

AUTO-DRAFT

®

VSUB-SERIES

VSUB BLOWERS

For providing combustion air; sidewall or
vertically venting heating appliances, dryers
and ovens.  Can be installed indoors or 
outdoors.

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794
PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547
Visit our web site • www.tjernlund.com

Listings:

ETL CERTIFIED TO:
UL 378 - Draft Equipment / Variable Speed
UL 705 - Power Ventilators
CSA-CAN3-B255-M81

RECOGNIZE THIS SYMBOL AS AN INDICATION OF IMPORTANT SAFETY INFORMATION!

!

Summary of Contents for AUTO-DRAFT VSUB Series

















Reviews: