background image

Thor Gas Griddle   

 

Technical Service Manual

 

Model: GH105-P, GH105-N, GH106-P, GH106-N

 

IMPORTANT FOR FUTURE REFERENCE

 

Please complete this information and retain this manual for the life of the equipment. For Warranty 
Service and/or parts, this information is required. 

                                                                             

Model Number                     Serial Number                 Date Purchased 

WARNING:

 For your safety, do not store or use gasoline or other flammable vapors or 

liquids in the vicinity of this or any other appliances. Keep the area free and clear of 
combustible.  

WARNING

Improper installation, adjustment, alteration, service or maintenance can 

cause property damage, injury, or death. Read the installation operating and 
maintenance instructions thoroughly before installing, or servicing this equipment. 

WARNING

Instructions must be posted in a prominent location. All safety 

precautions must be taken in the event the user smells gas. Safety information can be 
obtained from your local gas  supplier. 

15 Badgally Road, Campbelltown                                                                    

NSW 2560

 

 

Summary of Contents for GH105-N



































Reviews: