Texas Instruments OPA462EVM User Manual Download | Manualshive

Page: 1 / 13

background image

1

SBOU175 – October 2019

Submit Documentation Feedback

Copyright © 2019, Texas Instruments Incorporated

OPA462EVM

User's Guide

SBOU175 – October 2019

OPA462EVM

This user's guide describes the characteristics, operation, and use of the evaluation module (EVM) for the
OPA462. The EVM is designed to evaluate the performance of the devices in both single and dual-supply
configurations. This document also includes the schematic, printed circuit board (PCB) layout, and a bill of
materials (BOM). Throughout this document the terms

evaluation board

,

evaluation module

, and

EVM

are

synonymous with OPA462EVM.

WARNING

Danger: HIGH VOLTAGE! This evaluation board is intended for
professional use only. It has exposed high voltages. Do not
operate this board without proper high-voltage/high-current safety
practices. Read

Section 1.4

before using the EVM.

1
2
3
...
»

Summary of Contents for OPA462EVM














Reviews:

No comments

Related manuals for OPA462EVM

Brand: Balluff Pages: 62

Brand: Lantronix Pages: 8

Brand: Qiyang Pages: 27

Brand: Texas Instruments Pages: 17

Brand: Supero Pages: 107

Brand: Gigabyte Pages: 96

Brand: Microchip Technology Pages: 2

PRESTIGE X570 CREATION

Brand: MSI Pages: 88

Brand: CHAINTECH Pages: 49

Brand: Seco Pages: 49

Brand: Biostar Pages: 68

SBC86620 Series

Brand: AXIOMTEK Pages: 90

Brand: ASROCK Pages: 2

Brand: Sony Pages: 7

Brand: Sony Pages: 138

Brand: Abit Pages: 96

Brand: Telit Wireless Solutions Pages: 49

Brand: NXP Semiconductors Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands