Texas Instruments ADC08L060EVM Скачать руководство пользователя

Страница: 1 / 16

SLAU712 – February 2017

ADC08L060 Evaluation Module

User's Guide

SLAU712 – February 2017

ADC08L060 Evaluation Module

This user's guide describes the function and use of the ADC08L060 evaluation module (EVM). Included in
this document are a quick-start guide, instructions for optimizing evaluation results, jumper and connector
descriptions, software description, and alternate hardware configurations.

Contents

Overview

......................................................................................................................

1.1

Required Hardware

.................................................................................................

1.2

Required Software

..................................................................................................

1.3

Evaluation Board Feature Identification Summary

.............................................................

1.4

References

..........................................................................................................

Quick-Start Guide

............................................................................................................

2.1

Software Installation

................................................................................................

2.2

Hardware Setup Procedure

.......................................................................................

2.3

Software Setup Procedure

.........................................................................................

2.4

Quick-Start Troubleshooting

.......................................................................................

Optimizing Evaluation Results

.............................................................................................

3.1

Clocking Optimization

..............................................................................................

3.2

Coherent Input Source

.............................................................................................

3.3

HSDC Pro Settings

.................................................................................................

Alternate Hardware Configurations

......................................................................................

4.1

Clocking Options

..................................................................................................

4.2

Voltage Reference Options

......................................................................................

Appendix A

Jumper and Connector Descriptions

............................................................................

List of Figures

EVM Feature Locations

.....................................................................................................

Quick-Start Test Setup

......................................................................................................

HSDC Pro GUI Main Panel

.................................................................................................

Data Capture Results From Quick-Start Procedure

.....................................................................

List of Tables

Quick-Start Performance Measurements

.................................................................................

Troubleshooting Tips

........................................................................................................

HSDC Pro Settings to Optimize Results

..................................................................................

Jumper Descriptions and Default Settings

..............................................................................

Connector Descriptions

....................................................................................................

Trademarks

Microsoft, Windows are registered trademarks of Microsoft Corporation.

Содержание ADC08L060EVM

















Результаты поиска

Содержание ADC08L060EVM

Отзывы:

Похожие инструкции для ADC08L060EVM

Бренды по названию

Популярные бренды

Texas Instruments ADC08L060EVM, Руководство пользователя

Результаты поиска

Содержание ADC08L060EVM

Отзывы:

Похожие инструкции для ADC08L060EVM

Бренды по названию

Популярные бренды