background image

users

guide

OPAL 2000 SERIES

(Includes models: 2011, 2011S, 2006, 2006S)

REQUIREMENTS OF PART

68

FCC RULES

This device has been granted a registration number by the Federal Communications Commission, under Part 68 rules
and regulations for direct connection to the telephone lines. In order to comply with these FCC rules, the following
instructions must be carefully read and applicable portions followed completely:
1. Direct connection to the telephone lines may be made only through the standard modular cord furnished, to the
utility installed jack. No connection  may be made to party or coin phone lines. On the bottom of the phone is a label
that contains among other information, the FCC Registration Number and the Ringer Equivalence number (REN) for
this equipment. If requested this information must be provided to the telephone company. The USOC Jack for this
equipment is RJ11C.
2. The telephone company, under certain circumstances, may temporarily discontinue and make changes in facilities
and services which may affect the operation of the users' equipment: however, the user shall be given adequate notice
in writing to allow the user to maintain uninterrupted service.
3. In certain circumstances, it may be necessary for the telephone company to request information from you concern-
ing the equipment which you have connected to your telephone line. Upon request of the telephone company, provide
the FCC registration number and the ringer equivalence number of the equipment which is connected to your line;
this information will be found on the device.
4. If any of your telephone equipment is not operating properly, you should immediately remove it from the telephone
line. It may cause harm to the telephone network.
5. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will
notify you in advance disconnection. If advance notice is not feasible, the telephone company must; promptly notify
you of such temporary discontinuance; afford the opportunity to correct the condition; inform you of your rights to
bring a complaint to the FCC under their rules.
6. Repairs to the device may be made only by the manufacturer or an authorized service agency. This applies at any
time during and after warranty. If unauthorized repair is performed, registration, connection to the telephone lines and
remainder of warranty period all become null and void.
7. This equipment is hearing aid compatible.

REQUIREMENTS OF PART

15

FCC RULES

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio communications. However, there
is not a guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: -Move the telephone away
from the receiver. -Consult the dealer or an experienced radio/TV technician for help. Any changes made by the user
not approved by the manufacturer can void the user's authority to operate the telephone. 

INDUSTRY OF CANADA REQUIREMENTS

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets
certain telecommunications network protective operational and safety requirements as prescribed in the appropriate
Terminal Equipment Technical Requirements documents. The department does not guarantee the equipment will
operate to the users satisfaction. Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a represen-
tative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment mal-
functions, may give the telecommunications company cause to request the user to disconnect the equipment. Users
should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and
internal metallic water pipe systems, if present, are connected together. This precaution may be particularly important
in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appro-
priate electric inspection authority or electrician, as appropriate.

The Ringer Equivalence Number (REN) of this device is Z.

Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maxi-
mum number of terminals allowed to be connected to a telephone interface. The termination on an interface may con-
sist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of
all the devices does not exceed 5. This telephone connects to the telephone network under the connecting arrangement
code CA11A.

Copyright © 2004 Teledex LLC. All rights reserved.        606-2700-00

Thank you for purchasing

a Teledex telephone!

Summary of Contents for Opal Series 2006

Page 1: ...ence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is not a guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television receptio...

Page 2: ...g bracket slots located near the middle of the telephone Then firmly push down to insert the retaining tabs on the opposite side of the mounting bracket 7 Connect a short modular line cord into the jack on the back of the phone labeled LINE Route the line cord through the line cord channel Connect the other end of line cord to the phone jack on the wall mounting plate 8 Turn the telephone over and...

Page 3: ...THE HANDSET 1 Lift the handset The Opal will select the ringing line 2 To end the call hang up the handset 1 PROGRAMMING THE AUTO DIAL KEYS The Opal 2000 series has up to eleven 11 programmable AUTO DIAL keys Follow the steps below to program the keys to automatically dial telephone numbers or to activate tele phone system features To program the auto dial keys the telephone must be connected to a...

Page 4: ...IPPED MODELS ONLY To activate the handset from speakerphone mode 1 Lift the handset from the cradle 2 The red SPEAKER LED will go out TO ACTIVATE THE SPEAKERPHONE FROM HANDSET MODE SPEAKERPHONE EQUIPPED MODELS ONLY 1 Press the SPEAKER key 2 The red SPEAKER LED will indicate speakerphone selection 3 Place the handset back into the cradle USING THE HOLD KEY The HOLD key places the call on hold local...

Reviews: