background image

iPhone DECT Cordless Series User Guide

For Models AC8205S, AC8210S (1.8 GHz) and AC9205S, AC9210S (1.9 GHz)

Preparing to Use the AC8200/AC9200 Series

1.  Prepare to install the battery into the cordless handset  
  by removing the battery cover  and sliding it off. If cover is  
  secured with a screw, remove the screw first.
2. Insert the battery connector into the handset’s connector.
  The connector is “keyed” so it only goes in one way.
  Do not force the connection.

Note: The handset may “beep” when the battery is  
connected. This is not an indication that the telephone
is ready to use. To obtain optimal performance of the
telephone, be sure to charge the battery for 10 to 12 hours.

3. Replace the battery compartment cover and the  
  retaining screw.
4. Insert the provided rubber screw cover.
5. Turn the telephone base so the back panel is facing you.
  Insert either end of the RJ-45 cable into the jack on the     
  back of the telephone labeled LINE.
6. Insert the other end of the cable into the jack on the AC
  adapter labeled PHONE.
7. Insert one end of the RJ-11 line cord into the jack on the   
  AC adapter labeled LINE.
8. Insert the other end of this line cord into a telephone jack.
9. Plug the AC adapter into an unswitched electrical outlet.
10. Remove the plastic overlay and place the paper faceplate
    (supplied separately) over the keys. Replace the plastic
    overlay by hooking the tabs on the overlay into the
    recessed slots located on both sides.
11. Place the cordless handset on the base unit.
    The handset/base registration process will occur.

Handset/Base Registration Procedure

This procedure establishes an exclusive link between a specific
handset and base, thereby allowing no other access to this
specific base. To accomplish this procedure, place the handset
on the base in the charging position. The LINE indicator will
blink while the registration process is occuring. This process 
only occurs the first time a handset is placed on the charging 
cradle of a new base.

Charging the Battery

The rechargeable Lithium-Polymer battery must be fully 
charged before using the phone for the first time. 

It is recommended that the battery be charged for approxi-
mately 10 to 12 hours without interruption before use.
To charge the battery, place the handset, keypad down, in the 
base unit. Ensure that  the CHARGE LED on the base lights.

If the LED Does Not Light:

1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is plugged into an 

unswitched

  electrical outlet.
3. Ensure that the handset charging contacts at the bottom of
  the handset are making good contact with the base unit’s
  charging contacts.

Cleaning the Battery Contacts

To maintain a good charge, it is important to clean all  
charging contacts on the handset and base unit. Use a  
pencil eraser or other contact cleaner. Do not use any  
liquids or solvents.

Battery Safety Instructions

1. Use only Teledex-approved battery replacements.
2. Dispose of the Lithium-Polymer battery in any ordinary    
  trash receptacle.
3. Do not dispose of battery in fire, as it may explode.
4. Charge the battery only while in the handset, and only by
  using the base unit to charge. Do not attempt to remove
  the battery and charge it in a separate charging unit.
5. Do not short-circuit the battery, as this may cause it to
  explode or catch fire.

Adjusting the Ring Volume and Assigning Ring Tones

The UP and DOWN volume keys will adjust the ringer volume 
of the telephone. To adjust ring volume, press either the UP 
and DOWN volume key when the handset is on the bse cradle 
and the phone is not active (off-hook). 

There are four ring tones that can be assigned individually 
to either line (on two-line models) to audibly identify the 
ringing line. Additionally, the AC8200/AC9200 series features 
a programmable “crescendo” ring mode, wherein the ring 
volume begins at the lowest setting, then rings progressively 
louder with each ring during an incoming call. 

To assign a ring tone to a line (normal ring mode):

1. Press the FLASH key (see Fig. 1); then a key on the dial pad
  from 1-4, depending on the desired ring tone. The phone
  will ring once to provide a sample of the selected ring
  tone. 
2. When you have selected a suitable ring tone, press the
  STORE key (see Fig. 1), then a number on the dial pad for
  the desired line assignment (i.e.; ‘1’ for line 1, ‘2’ for line 2).

Cordless Handset 
AC Adapter
Base Unit 
User Guide
Lithium Polymer Battery
Clear Plastic Overlay 

Rubber Battery Screw Cover 
Phillips Screw
15-foot, 8-wire Cable
   

(with RJ-45 connector)

10-foot, 4-wire Line Cord  
   

(with RJ-11 connector)

Included in Your Package

Summary of Contents for AC8205S

Page 1: ... without interruption before use To charge the battery place the handset keypad down in the base unit Ensure that the CHARGE LED on the base lights If the LED Does Not Light 1 Ensure that the AC adapter is plugged in 2 Ensure that the AC adapter is plugged into an unswitched electrical outlet 3 Ensure that the handset charging contacts at the bottom of the handset are making good contact with the ...

Page 2: ... flickering red LED indicate an incoming call To answer a call using the handset while it is not on the base 1 Pick up the handset 2 Press the line key for the ringing line The handset will go off hook answering the ringing line 3 To end the call place the handset in the base unit cradle or press the illuminated line key on the handset To answer a call using the handset while it is resting on the ...

Page 3: ...th the mounting posts The Ringer Equivalence Number REN of this device is 0 7B Notice The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equival...

Page 4: ...tions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reori...

Reviews: