TECNICOMAR BICOMPACT Instructions For The Installation, Use And Maintenance Download

Page: 1 / 42

Instructions for the installation, use and maintenance of Tecnicomar watermaker

1-1

INSTRUCTIONS FOR THE INSTALLATION, USE AND MAINTENANCE OF

TECNICOMAR WATERMAKERS

Models

MINIMAR PLUS

SAILOR

BICOMPACT

NOTE

The indications contained in this Manual must be strictly followed during installation, operation and
maintenance of the watermaker in order to warrant the operators' safety and the equipment
maximum efficiency.

Identification

The Tecnicomar watermaker carries a plate with the following data:
a)

Manufacturer: TECNICOMAR SpA, C/da Berbaro n.145/D – 91025 Marsala – ITALY –
Tel.0923-969409 / Fax 0923-960235;

CE logo;

Type

Serial number

Year of manufacture

Voltage

Revision 1

2009

Revision

07/2011

Revision

03/2012

Revision

03/2013

Revision

12/2014

Revision

08/2015

CONTROL BOX TINY2 DESCRIPTION UPDATED

Summary of Contents for BICOMPACT











































Search results

Summary of Contents for BICOMPACT

Reviews:

Related manuals for BICOMPACT

Brands by name

Popular brands

TECNICOMAR BICOMPACT, Instructions For The Installation, Use And Maintenance

Search results

Summary of Contents for BICOMPACT

Reviews:

Related manuals for BICOMPACT

Brands by name

Popular brands