![background image](http://html1.mh-extra.com/html/taymor/madera/madera_installation-instructions_823435001.webp)
✁
1
HINGES
HINGES
A.
LEFT
HANDING
B.
RIGHT
HANDING
INSTALLATION INSTRUCTIONS
MADERA
TOOLS AND MATERIALS REQUIRED
>
Drill
>
2-1/8” (54 mm) Hole Saw
>
Chisel
>
3/8” (10 mm) Drill Bit
>
Phillips Screw Driver
>
1” (25 mm) Wood Bit
>
Tape Measure
DETERMINE DOOR HANDING
Stand at the exterior side and face the door.
A. Your door is a LEFT HAND door if hinges
are installed at your left hand.
B. Your door is a RIGHT HAND door if hinges
are installed at your right hand.
2a
USE THROUGHBOLT TEMPLATE TO MARK
AND DRILL HOLES
2. DRILL HOLES
Select backset. Mark and drill
holes as shown.
1”
(25 mm)
3/8”
(10 mm)
2-1/8”
(54 mm)
2b
IF REPLACING EXISTING HANDLESET OR INSTALLING ON PRE-DRILLED
DOOR, CHECK DOOR JAMB AND DOOR PREPARATION
2-1/8”
(54 mm)
5”
(127mm)
2-1/8”
(54 mm)
3/8”
(10 mm)
1” (25 mm)
1” (25 mm) or 7/8” (22 mm)
OR
OR
8-5/8” (219 mm)
Chisel outlines for strike plates until they sit
flush with door edge.
1-1/2” (38 mm) High
1” (25 mm) Wide
1-3/16” (30 mm ) Deep
1” (25 mm) Radius
5/16” (8 mm) Deep
1. MARK DOOR
Use template attached to mark
holes on door face.
A. Make mark for 1”(25 mm) hole
on door edge.
B. Height 36” (914 mm) to 38”
(965 mm) from floor.
Backset
2-3/8” (60 mm)
or
2-3/4” (70 mm)
3
CHOOSE LATCH FACE PLATE FOR HANDLESET & DEADBOLT
Chisel 1/8” (3 mm) deep or until
latch face plate is flush with door
edge.
RADIUS OR SQUARE CORNER
MORTISE
DRIVE-IN
1
2
3
Ø
3/8” (
10
m
m
)
8-5/8” (219 mm)
CENTER TO CENTER
FEB. 2014
1-3
/4
”
(45 m
m
)
1-3/8
”
(3
5
m
m
)
1-9
/1
6”
(40
m
m
)
1-3
/4
”
(45 m
m
)
1-3/8
”
(3
5
m
m
)
1-9
/1
6”
(40
m
m
)
Mark Height 36" (914 mm) from Floor to Center
2-3
/4” (
70 mm)
2-3/8” (60 mm)
Ba
ckse
t
Fold here. P
la
ce on door ed
ge
.
CARE AND MAINTENANCE
The following care instructions should be followed to ensure a long lasting finish:
1. Remove locks, or do not install locks, prior to painting your door.
2. Periodically clean with mild soap and a soft cloth only.
3. Do not use abrasives or harsh chemicals
D
ri
ll
1
” (
25 mm) hole a
t
ce
nt
er of door edg
e.
D
ri
ll
1
” (
25 mm) hole a
t
ce
nt
er of door edg
e.
5” (127 mm)
Ø
2-
1/8 “
(54 mm
)
Ø
2-
1/8 “
(54 mm
)
CENTER TO CENTER
Ba
ckse
t
IMPORTANT! TEMPLATE MUST PRINT AT 1/1 SCALE
Sheet size: 11” x 17”
(280mm x 432mm)