Task Force Tips ZCF1T3 Instructions For Installation Manual Download

Page: 1 / 24

©Copyright Task Force Tips LLC 2014-2018

LIZ-060 October 26, 2020 Rev03

TASK FORCE TIPS LLC

MADE IN USA · tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

G-Force

INSTRUCTION FOR INSTALLATION, SAFE OPERATION, AND MAINTENANCE

SAMPLE CONFIGURATIONS

BOOSTER and BOOSTER OSC

SECONDARY LDH INLET

FOR MONITORS

DANGER

Understand manual before use. Operation of this device without understanding the manual and

receiving proper training is a misuse of this equipment. Obtain safety information at tft.com/

serial-number.
This equipment is intended for use by trained and qualified emergency services personnel for

firefighting. All personnel using this equipment shall have completed a course of education

approved by the Authority Having Jurisdiction (AHJ).
This instruction manual is intended to familiarize firefighters and maintenance personnel with the

operation, servicing, and safety procedures associated with this product. This manual should be

kept available to all operating and maintenance personnel.

Model ZCF1T3

integrated with

TFT Hydrant Under Monitor

and TFT Monsoon Monitor

Model ZCH1T1-OSC

for attachment to Hydrants,

Valves and Monitors with
4" ANSI 150 connections

Model ZCH1TQ

integrated with

TFT Industrial Valve Under Monitor and
4.5" NH Quick Connect for TFT monitor

HYDROSTATIC PROOF TEST:

800 psi (55 bar)*

*Do not exceed the rated operating pressure of 200 psi (14 bar).

Per FM 1421 the hydrostatic proof test is performed on a sample

valve to ensure it does not visibly rupture, crack or permanently

distort at 4 times the rated operating pressure. The purpose of the

proof test is to be confident the valve design may be safely

operated at the rated operating pressure.

RATED OPERATING PRESSURE:

200 PSI (14 BAR)

SAFE OPERATING RANGE FOR MONITOR OUTLET:

Booster and Booster OSC: 2000 gpm @ 200 psi

(8000 l/min @ 14 bar).
Booster only (not OSC): 2500 gpm @ 130 psi

(9500 l/min @ 9 bar).

Summary of Contents for ZCF1T3

























Search results

Summary of Contents for ZCF1T3

Reviews:

Related manuals for ZCF1T3

Brands by name

Popular brands

Task Force Tips ZCF1T3, Instructions For Installation Manual

Search results

Summary of Contents for ZCF1T3

Reviews:

Related manuals for ZCF1T3

Brands by name

Popular brands