![background image](http://html.mh-extra.com/html/system-sensor/2112lp/2112lp_installation-and-maintenance-instructions_1422267001.webp)
D150-03-00
1
I56-597-03R
B112LP Plug-in Detector Base
For use with the following smoke detectors:
IN US:
1151, 2151
IN CANADA: 1151A, 2151A
IN EUROPE:
1151E, 2151E
INSTALLATION AND MAINTENANCE INSTRUCTIONS
3825 Ohio Avenue, St. Charles, Illinois 60174
1-800-SENSOR2, FAX: 630-377-6495
www.systemsensor.com
Before Installing
Please thoroughly read the System Sensor manual I56-407,
Guide for Proper Use of System Smoke Detectors
, which pro-
vides detailed information on detector spacing, placement,
zoning, wiring, and special applications. Copies of this
manual are available at no charge from System Sensor. (For
installation in Canada, refer to CAN/ULC-S524,
Standard
for the Installation of Fire Alarm Systems
and CEC Part 1,
Sec. 32.)
NOTICE:
This manual should be left with the owner/user
of this equipment.
IMPORTANT:
The detector used with this base must be
tested and maintained regularly following NFPA 72 require-
ments. The detector used with this base should be cleaned
at least once a year.
Specifications
Base Diameter:
6.2 inches (157 mm)
Base Height:
0.95 inches (24 mm)
Weight:
0.3 lb. (137 g)
Mounting:
4-inch square box with or without plaster ring. Min. depth–1.5 inches
3-1/2-inch octagon box. Min. depth–1.5 inches
Operating Temperature Range:
0° to 49°C (32° to 120°F)
Operating Humidity Range:
10% to 93% Relative Humidity, Noncondensing
Electrical Ratings - includes base and detector
System Voltage:
24 VDC
Maximum Ripple Voltage:
4 Volts peak-to-peak
Start-Up Capacitance:
0.02µF Maximum
Standby Ratings:
20 VDC Minimum
29 VDC Maximum
120 µA Maximum
Alarm Ratings:
17 mA Minimum
36 mA Maximum
Reset Voltage:
1.4 VDC Minimum
Reset Time:
0.3 Seconds Maximum
(The optional RA400Z operates within specified detector alarm currents.)
Start-up Time:
34.0 Seconds Maximum
Relay Contact Ratings:
Resistive or Inductive (60% Power Factor)
Form A:
2.0 A @ 30 VAC/DC
Form C:
2.0 A @ 30 VAC/DC
0.6 A @ 110 VDC
1.0 A @ 125 VAC
General Description
The Model B112LP detector base is designed for use with
System Sensor model 2151 photoelectronic and 1151 ioniza-
tion detector heads. This four-wire base is equipped with
screw terminals for the connection of power, ground, and
an optional remote annunciator.
Mounting
The detector base mounts directly to 3-1/2 inch and 4-inch
octagon boxes and 4-inch square boxes, with or without
plaster rings. To mount the base, remove the decorative
ring by rotating it in either direction to unhook the snaps
before separating the ring from the base. Use the screws
supplied with the junction box to attach the base to the
box through the appropriate slots in the base (see Figure
1). Position the decorative ring around the base and rotate
it in either direction until the ring snaps into place.
D150-03-00
4
I56-597-03R
©2001 System Sensor
Three-Year Limited Warranty
System Sensor warrants its enclosed smoke detector base to be free from
defects in materials and workmanship under normal use and service for a
period of three years from date of manufacture. System Sensor makes no
other express warranty for this smoke detector base. No agent, represen-
tative, dealer, or employee of the Company has the authority to increase
or alter the obligations or limitations of this Warranty. The Company’s
obligation of this Warranty shall be limited to the repair or replacement
of any part of the smoke detector base which is found to be defective in
materials or workmanship under normal use and service during the three
year period commencing with the date of manufacture. After phoning
System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return
Authorization number, send defective units postage prepaid to: System
Sensor, Repair Department, RA #__________, 3825 Ohio Avenue, St.
Charles, IL 60174. Please include a note describing the malfunction and
suspected cause of failure. The Company shall not be obligated to repair
or replace units which are found to be defective because of damage,
unreasonable use, modifications, or alterations occurring after the date
of manufacture. In no case shall the Company be liable for any conse-
quential or incidental damages for breach of this or any other Warranty,
expressed or implied whatsoever, even if the loss or damage is caused by
the Company’s negligence or fault. Some states do not allow the exclu-
sion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This Warranty gives you
specific legal rights, and you may also have other rights which vary from
state to state.
Please refer to insert for the Limitations of Fire Alarm Systems
I56-
597-03R