background image

G

 

The lightning flash

 with arrowhead 

symbol within an equilateral triangle is 
intended to alert the user of the presence 
of uninsulated “dangerous voltage” within 
the product’s enclosure that may be of 
sufficient magnitude to constitute a risk of 
electric shock to persons. The exclamation 
point within an equilateral triangle is 
intended to alert the user of the presence 
of important operating and maintenance 
(servicing) instructions in the literature 
accompanying the product (i.e. this Quick 
Start Guide).

G

 

CAUTION:

 To prevent electric shock, do 

not use the polarized plug supplied with the 
device with any extension cord, receptacle, 
or other outlet unless the prongs can be 
fully inserted.

G

 

Power Source:

 This Symetrix hardware 

uses a universal input supply that 
automatically adjusts to the applied 
voltage. Ensure that your AC mains voltage 
is somewhere between 100-240 VAC, 
50-60 Hz. Use only the power cord and 
connector specified for the product and 
your operating locale. A protective ground 
connection, by way of the grounding 
conductor in the power cord, is essential 
for safe operation. The appliance inlet and 
coupler shall remain readily operable once 
the apparatus has been installed.

G

  Lithium Battery Caution:

 Observe the 

correct polarity when changing the lithium 
battery. There is a danger of explosion if 
battery is incorrectly replaced. Replace only 
with the same or equivalent type. Dispose 
of used batteries according to local 
disposal requirements.

G

 

User Serviceable Parts:

 There are no 

user serviceable parts inside this Symetrix 
product. In case of failure, customers 
inside the U.S. should refer all servicing to 
the Symetrix factory. Customers outside 
the U.S. should refer all servicing to an 
authorized Symetrix distributor. Distributor 
contact information is available online at: 

http://www.symetrix.co

.

AVIS:

NE PAS OUVRIR

Il ne se trouve a l’interieur aucune piece pourvant entre reparée l’usager.

SEE OWNERS MANUAL. VOIR CAHIER D’INSTRUCTIONS.

S’adresser a un reparateur compétent.

RISQUE DE CHOC ELECTRIQUE

No user serviceable parts inside. Refer servicing to qualified service personnel.

CAUTION

WARNING:

TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE

DO NOT OPEN

RISK OF ELECTRIC SHOCK

Important Safety Instructions

!

  Read these instructions.

@

  Keep these instructions.

#

  Heed all warnings.

$

  Follow all instructions.

%

  Do not use this apparatus near water. This 

apparatus shall not be exposed to dripping 
or splashing and no objects filled with 
liquids, such as vases, shall be placed on 
the apparatus.

^

  Clean only with dry cloth.

&

  Do not block any ventilation openings. 

Install only in accordance with the 
manufacturer’s instructions.

*

  Do not install near any heat sources such 

as radiators, heat registers, stoves, or 
other apparatus (including amplifiers) that 
produce heat.

(

  This apparatus shall be connected to 

a mains socket outlet with a protective 
earthing connection. Do not defeat 
the safety purpose of the polarized or 
grounding-type plug. A polarized plug has 
two blades with one wider than the other. 
A grounding type plug has two blades and 
a third grounding prong. The wide blade 
or the third prong are provided for your 
safety. If the provided plug does not fit 
into your outlet, consult an electrician for 
replacement of the obsolete outlet.

BL

  Ensure proper ESD control and grounding 

when handling exposed I/O terminals.

BM

  Protect the power cord from being walked 

on or pinched particularly at plugs, 
convenience receptacles, and the point 
where they exit from the apparatus.

BN

  Only use attachments/accessories 

specified by the manufacturer.

BO

  Use only with the cart, stand, tripod, 

bracket, or table specified 
by the manufacturer, 
or sold with the 
apparatus. When a cart is 
used, use caution when 
moving the cart/apparatus 
combination to avoid injury from tip-over.

BP

  Unplug this apparatus during lightning 

storms or when unused for long periods of 
time.

BQ

  Refer all servicing to qualified service 

personnel. Servicing is required when the 
apparatus has been damaged in any way, 
such as power-supply cord or plug cord 
is damaged, liquid has been spilled or 
objects have fallen into the apparatus, the 
apparatus has been exposed to rain or 
moisture, does not operate normally, or has 
been dropped.

Note:

 This equipment has been tested and found to comply with the limits 

for a Class B digital device, pursuant to part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will 
not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected. 

•  Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the 
user’s authority to operate the equipment under FCC rules.
Cet appariel numerique de la classe B respecte toutes les Exigences du 
Reglement sur le materiel brouilleur du Canada.

1 of 4

QUICK START GUIDE:

 Edge

www.symetrix.co 

+1.425.778.7728

What Ships in the Box

•  Edge hardware device.
•  9 detachable three position 3.81 mm terminal 

block connectors.

•  A North American (NEMA) or Euro IEC 

power cable. You may need to substitute a 
cable appropriate for your locale.

•  This Quick Start Guide.

What You Need to Provide

A Windows PC with 1 GHz or higher 
processor and:
•  Windows 7 or higher.
•  250 MB free storage space.
•  1280x1024 graphics capability.
•  16-bit or higher colors.
•  Internet connection.
•  512 MB or more of RAM as required by 

your operating system.

•  Network (Ethernet) interface.
•  CAT5/6 cable or an existing Ethernet 

network.

Getting Help

Composer, the Windows software that 
configures Edge hardware, includes a help 
module which acts as a complete User’s 
Guide for both hardware and software. If you 
have questions beyond the scope of this 
Quick Start Guide, contact our Customer 
Support Group in the following ways:

Tel: +1.425.778.7728
 

6:00 am to 6:00 pm

 

Monday through Friday,

 

Pacific Time

Web: http://www.symetrix.co
Email: [email protected]
Chat:      http://symetrix.casengo.com/vip/

Summary of Contents for Edge

Page 1: ...into your outlet consult an electrician for replacement of the obsolete outlet BL Ensure proper ESD control and grounding when handling exposed I O terminals BM Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus BN Only use attachments accessories specified by the manufacturer BO Use only with the ca...

Page 2: ...ct to Edge directly Even if the PC s default settings have been changed Edge will try to establish communications by setting up appropriate routing table entries to reach devices with 169 254 x x addresses Connecting to Edge from a host computer on the same LAN Both Edge and the host computer require the following 3 items 1 IP Address The unique address of a node on a network 2 Subnet Mask Configu...

Page 3: ...sk and Gateway Click OK when finished Now back in the locate hardware dialog ensure the Edge device is selected and click Select Hardware Unit to use this Edge hardware in your Site File Close the Locate Hardware dialog IP Configuration with the Front Panel Edge IP information can also be edited from the front panel Edge s front panel interface starts up in System Mode out of the box Press LEFT or...

Page 4: ...ratches and dents unless failure has occurred due to a defect in materials or workmanship within the warranty period 7 Conditions caused by normal wear and tear or otherwise due to the normal aging of Symetrix products 8 Damage caused by use with another product 9 Product on which any serial number has been removed altered or defaced 10 Product that isn t sold by an authorized Symetrix Dealer or D...

Reviews: