LED Dimmable Panel Light with White Frame
User Manual
Part Number:
Important: Read all instructions prior to installation.
LPD-40K24-40
Surface Mounting Kit: LPD-SMK24
Recessed Mounting Kit: LPD-JBK
Summary
These 0-10V dimmable ETL Listed 2’x4’ recessed or surface mount panel
lights are perfect for new construction applications or replacing existing
fl uorescent troff er fi xtures with recessed installation. Use Recessed
Mounting Kit (LPD-JBK) for T-bar ceiling installations. Use Surface
Mounting Kit (LPD-SMK24) for surface mounting installations.
Note: Recessed Mounting Kit
Required (LPD-JBK)
1. Turn off power and remove
existing fixture or remove ceiling tile.
2. Bend each t-bar suspension
hook away from panel until facing
perpendicular to panel backing. Bend
hook arm until facing perpendicular
to hook body. Hook panel light onto
t-bar until panel is fully supported.
(Fig. 2 & 3)
3. Remove the knock-out hole on
the Junction Box. Run wiring through
hole and secure. Insert supply
Line and Neutral power wires into
corresponding locations on orange
quick disconnect. Line is labeled in black,
neutral is white. Connect the green ground wire
to supply ground wire. Connect the two orange
quick disconnects together. Connect the 0~10V
dimming wires according to the Wiring Diagram
with wire nuts. (Fig. 4)
4. Attach Junction Box to panel backing by
inserting the tabs from the Junction Box into
the slots on the panel backing and secure with
Thumb Screw. (Fig. 5)
4400 Earth City Expy, St. Louis, MO 63045
866-590-3533 superbrightleds.com
Specifi cations
Recessed Installation
Input Voltage
100-277 VAC
Input Power
40 Watts
Input Current
343mA
Lumens
4500 lm
Color Temperature
4000K
CRI
83
Effi cacy
125 lm/w
Temperature Range
-4° ~ 104° F (-20° ~ 40°C)
Dimensions
L47.75” x W23.75” x H.67” (121.3 x 60.3 x
1.7cm)
Panel Weight
16 lbs 5oz (7399g)
J-Box Mounting Plate Weight
5lbs 4oz (2381g)
Warranty
5 years
Included Parts
FS SERIES
Surface Mounted Kit
Installation
FS SERIES
Surface Mounted Kit
Installation
S tep2:
Turn off power. Insert the L,N wires
of the J-box into the male connector.
2
S tep6:
Plug the female connector of the
luminaire into the male connector of the AC
input wire.The Ground connects to Green
wire.Dimming wires connect according to
the same wire color.
6
S tep4:
Alight the 2 longer hooks on the metal plate with
the longer hole on the luminaire(Look at the metal palte
and the luminaire with the 'STEP 1' mark). Slightly move
the luminaire forward and make sure the hooks is in
right position.
4
S tep1:
Remove the surface mounted kit
from the luminaire.
1
S tep5:
Fix the metal string on the hook.
(Fig.2)
5
S tep3:
Align the holes on the surface mounted kit with
the hole on the J-box Tighten 2#8-32 screws, rotate
the plate to your right position and lots of KA3.5*20mm
screws into the ceiling and make the kit flush with
the ceiling.
3
Step8:
Push the luminaire on the ceiling. Make
sure the 4 hooks are inside the luminaire and
push forward the luminaire until you hear a
clicking sound.
8-1
S tep7:
Put the wire into the J-box.
7-1
8-2
2
RECESSED INST
ALLA TION
FS SERIES
FS SERIES
INST ALLA TION
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice.
Please visit our website the most recent user guide versions.
NOTE
Unpack and carefully examine the product.
Report any damage and save all packing materials if any part(s) were damaged during shipping.
Do not attempt to use this apparatus if it is damaged.
UNP ACKING
1
2
3
Designed for use in 100V~277V,50-60Hz protected circuit. Apply class 2 power supply.
READ ALL INSTRUCTIONS BEFORE INST
ALLA TION
1
2
3
4
5
6
7
8
Consult a qualified electrician to ensure correct branch circuit conductor.
The product should be installed and operated by a qualified electrician or technician in
with relevant local codes.
accordance
Risk of electric shock. Ensure that main power source is off when wiring or soldering the
of the product.
sections
Before installing this fixture or doing any maintenance, make sure to turn off the power
the circuit breaker or fuse box.
supply at
Check to make sure that all fixture connections have been properly made and the fixture
grounded to avoid potential electrical shocks.
is
Do
in water.
not handle energized fixture when hands are wet, when standing on wet or damp surfaces, or
This
conditions to ensure safety to human body.
panel lights are normally set to work at extra low voltage below DC42V and constant current
OPTIONAL
FS22-DL-XXX, FS22-DM-XXX, FS24-DM-XXX, FS24-DH-XXX,VS14-DM**
Suitable for Damp location
. Access above ceiling required. Suitable for suspended ceilings
IMPORT ANT SAFETYINFORMA
TION
CAUTION: Risk of Electric Shock
!
Accessory:
LED Luminaire
Installation instruction
Surface mounted kit (for surface mounted)
J-box ( for recessed )
page 2
page 1
page 4
page 3
RECESSED INST
ALLA TION
Step3:
Turn off power,remove the ceiling panel. Then place
the panel in to the T-bar,ensure he panel is attached to the
ceiling.(Figure3)
Step4:
connect conduit to J-box with proper connector(s).
Remove appropriate round knock-out(s) and
Step5:
tightly.the line connect to the connector with the black
mark, the natural connect to another,the ground connect
to the green wire.(Figure4)
Put a connector to the end of AC input wire and
Step1:
Remove the surface mounted kit
from the luminaire.
Step2:
Same to 4 hang buckles.(Figure 2)
Bend hang buckle by 90° making it vertical to
the rear cover of panel light.
Step7:
Push all wires back into the junction box,Close J-BOX for cap (Figure 5).
please use switch to dim and don’t need to connect the dimming
wire. Dimming step:
Fristly
, Turn on to 100% brightness
Secondly
,It takes about 0.5~2 seconds from turn off the light to
next trun on and lamp is in 50% brightness,
At last
,It takes
about 0.5~2 seconds from turn off the light to next trun on and
lamp 10% brightness. (Figure 7)
Note: For cycle of step dimming, wait until the lamp is in brightness.
For failure of step dimming, turn off the lamp and turn on after 3 second.
For Step Dimming
,
For 0-10V Dimming
The driver PUR (D+) to the (PUR),and the
driver GRY(D-)to the dimmer-(GRY)
Connect the wires with terminal cap as shown in wiring
diagram (Figure 6).
Incoming insulated dimming conductors shall have
voltage rated at least equal to the branch voltage.
Compatible with 0-10V dimmer
Figure1
Figure2
Figure3
Figure4
Figure5
WIRING DIAGRAM
0-10V
Dimmer
D +
D -
PURPLE
GREY
L
N
G
PURPLE
GREY
RED BLACK
BLACK
WHITE
GROUND
LED
PANEL
Dimming
Driver
Figure6
Step Dimming
One Cycle
Note
:
After
3s
turn
on
lamp to
100
%
brightness
.
Turn Off
Lamp
Turn Off
Lamp
Turn Off
Lamp
Turn On
Lamp
10
%
brightness
Turn On
Lamp
50
%
brightness
Turn On
Lamp
100
%
brightness
After 0.5S
At
0
.
5
-
2s
At
0
.
5
-
2s
After 0.5S
After 0.5S
Figure7
To r igh t po s itio n
It is the right pos ition whic h is the
longer hooks of the firs t groove.
7-2
1
2
3
4
R ight pos ition
.67”
17.1mm
47.75”
1212.85mm
23.75”
603.23mm
Even-Glow™ Series
Recessed Mounting Kit (LPD-JBK) sold separately
Surface Mounting Kit (LPD-SMK24) sold separately
Panel Light (LPD-40K24-40)
1 - LED Light Panel with internal driver
1 - Junction Box
1 - Attachment Thumb Screw
1 - Surface Mount Bracket
7 - Screws
7 - Screw Anchors
1 -
Cable Service Loop
1 -
Cable Service Loop Screw
Rev Date: V1 08/04/2016
Wiring Diagram
Power Cycle Diagram
WIRING DIAGRAM
0-10V
Dimmer
D +
D -
PURPLE
GREY
LINE
NEUTRAL
GROUND
PURPLE
GREY
RED BLACK
BLACK
WHITE
GREEN
LED
PANEL
Dimming
Driver
