background image

Rev F Date: 11.2.2006 

R

888 Porter Rd.  Muskegon, MI  49441  Phone: 231.798.8888  Fax: 231.798.4960  www.structuralconcepts.com 

READ AND SAVE THESE INSTRUCTIONS 

OPEN REFRIGERATED SELF-SERVICE MERCHANDISER 

Model DO3637R 

38 1/8”L x 28 5/8”D x 37 1/4”H  (

Upper Display Case Only)

  

 

 

 

38 1/8”L x 28 5/8”D x 61 1/8”H  (

Upper Display Case + Drop-In Refrigeration Unit)

 

 
Model DO4837R 

50 1/8”L x 28 5/8”D x 37 1/4”H  (

Upper Display Case Only)

  

 

 

 

50 1/8”L x 28 5/8”D x 61 1/8”H  (

Upper Display Case + Drop-In Refrigeration Unit) 

 

Model DO3623R 

38 1/8”L x 28 5/8”D x 23 1/4”H  (

Upper Display Case Only)

  

 

 

 

38 1/8”L x 28 5/8”D x 47 1/8”H  (

Upper Display Case + Drop-In Refrigeration Unit) 

 

Model DO4823R 

50 1/8”L x 28 5/8”D x 23 1/4”H  (

Upper Display Case Only)

  

 

 

 

50 1/8”L x 28 5/8”D x 47 1/8”H  (

Upper Display Case + Drop-In Refrigeration Unit) 

 

Note 1. Internal counter height must be at least 28” for refrigeration and proper air flow space. 
Note 2. 

Model DO3637R & 3623R

: Service Top Cutout dimensions must be 27.15” Wide x 36.65” Long 

(with a minimum 1.42” perimeter) for proper clearance and fit of Drop-In Refrigerated Merchandiser.  
These combined dimensions require a 30” minimum counter top space for cutout.   
Note 3. 

Model DO4837R & DO23R

: Service Top Cutout dimensions must be 27.15” Wide x 48.65” 

Long (with a minimum 1.42” perimeter) for proper clearance and fit of Drop-In Refrigerated 
Merchandiser.  These combined dimensions require a 30” minimum counter top space for cutout.  

 

SERVICE DROP-IN REFRIGERATED MERCHANDISER 

L:\Inst & Oper Man\Oasis\DO(L)37R, DO(L)23R Operr Man 99574.pub 

 

 PN 99574 

INSTALLATION & 

OPERATING MANUAL 

Model DO4837R

 

Model DO3637R

 

Summary of Contents for DO3623R




























Reviews: