background image

Storm Drone 6 GPS

DEVO 7 Setup for NAZA-M Lite

- 1 -

Step 1

 - Set Fixed ID on the transmitter

Skip this part if you have a brand new  Storm Drone 6 GPS,
we have already done before we ship.

!

Make sure you have NOTHING plugged into BATT port on the RX701 receiver.

On the transmitter, goto MODEL > FIXED ID, press ENT, if it is showing the code, then 
press ENT again, press one more time, it's showing RUN, press "R" to choose NO, press 
ENT again, it's showing FIXID, press "R" again to choose OFF, then press EXT, and turn off 
transmitter.

Plug the bind plug into Batt port on the RX701 receiver, with this plug still in BATT port 
and power up the drone, you will see receiver flashing red slowly, then means old code 
has been erased, unplug drone battery and remove this bind plug.

Now you need to activate the Fixed ID function.
Turn on transmitter, then make sure Throttle Stick is all the way down, all trimming is 
neutral, both corner FMOD switch and Throttle Switch is off (pointing backward) and all 
switches on the transmitter pointing upward, then turn off transmitter.

Connect drone battery, the receiver will start flashing, place drone on flat surface.

Turn on transmitter, you should see black box running on the transmitter screen, do no 
touch anything or you will break the searching mode.

Do not touch anything (around 7-10 seconds) until transmitter stop flashing and you will 
see the RX701 receiver have solid light, that means binding has completed.

On the transmitter, goto MODEL > FIXED ID, turn it ON, then press DN button to confirm 
the code, then press ENT, and press ENT again to confirm, it will ask you to RUN, choose 
YES and press ENT. From now on your receiver is bound to this memory on your DEVO 7.

Now, you can turn the both the Heli or TX on and off at anytime and they will instantly bind 
when both are ON together.
 
Of course it is safer to never turn the TX off before the Heli, but if you do, the Heli will again 
bind if the TX is turned on.

1.

2.

3.

4.

5.

6.

7.

8.

Summary of Contents for 6 GPS










Reviews: