User’s Manual
StereoGraphics Corporation
2171 East Francisco Blvd., San Rafael, CA 94901
phone
800-783-2660 (within USA & Canada )
415-459-4500 (all other areas)
fax
415-459-3020
web site www.StereoGraphics.com
Installing the StereoGraphics Emitter
StereoGraphics
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
requires the use of an infrared emitter in order to synchronize the eyewear in
conjunction with the left and right image sequence on screen. The I/R receiver (located in the center of the
eyewear) must be in line of sight and in range of the emitter for successful operation of CrystalEyes. Please
consult the documentation accompanying your emitter for installation and operation details.
In all cases except for non-stereo-ready PCs, the system or graphics card manufacturer requires specific display
settings to enable Stereo3D mode. Please consult the manual or vendor for your specific graphics subsystem to
determine the proper settings for Stereo3D mode. For best results in using
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
with standard
workstation displays, set the emitter slightly behind the top edge of the monitor, as shown in Figure 1. In
addition:
Installation & Setup
Each pair of
Cr
Cr
Cr
Cr
CrystalEyes
ystalEyes
ystalEyes
ystalEyes
ystalEyes
eyewear includes two fresh batteries, which are installed at the factory. A compatible
stereo computer grapics or video system must be available to check the operation of the eyewear. To activate
the eyewear, unfold the temple pieces; to turn off the eyewear, fold the templepieces. When not in use, fold
your
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
eyewear with the temples laying flat across the back of the lenses for convenient storage.
Always fold the eyewear when not in use to maximize the battery life.
Always fold the eyewear when not in use to maximize the battery life.
Always fold the eyewear when not in use to maximize the battery life.
Always fold the eyewear when not in use to maximize the battery life.
Always fold the eyewear when not in use to maximize the battery life.
• For EPRO, ESGI and ELR emitters, make sure the emitter is switched
to the ON position. Depending on the emitter range needed, switch
the emitter to either the high or low setting.
• The ENT emitter will switch on and off automatically whenever a sync
signal is presented by the graphics card.
• Users of the EPC-2 must switch the emitter from BYPASS to STEREO
MODE and set the emitter range separately.
Figure 1. Display and Emitter
Prescription Glasses
If you normally wear prescription eyeglasses, place
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
CrystalEyes
over them. The eyewear will fit
comfortably over most prescription eyeglass frames.
For more information on setting up your system, please refer to our website at http://www.stereographics.com
Batteries
Two 3 V lithium/manganese dioxide
(NEDA 5004L), including:
Eveready
E-CR2032
Maxell
CR2032
Panasonic
CR2032
Ray-O-Vac
CR2032
Saft
LM2032
Optics
Shutters:
liquid crystal
Transmittance:
32% typical
Dynamic Range:
1000:1 typical
Close Time:
Less than 0.2 milliseconds
Open Time:
Less than 3 milliseconds
Field Rate:
80 to 160 fields per second
Bright Mode:
Automatically selected
Infrared Sensor
Angle of View:
90 degrees horizontal
140 degrees vertical
Weight
3.3 oz. (93 grams)
Controls
On/Off:
On/Off:
On/Off:
On/Off:
On/Off:
Eyewear operation is switched on and off
by unfolding and folding the eyewear temple pieces.
Bright mode
Bright mode
Bright mode
Bright mode
Bright mode
: Both lenses automatically switch to
full transparency for up to 8 minutes when shielded
from infrared signals. Restoring the infrared signal
returns the eyewear to full operation.
Sanyo
CR2032
Seiko
CR2032
Technacell
CR2032
Varta
CR2032
Duracell
DL2032
Specifications
