80877952
This Manual
Connecting a Tablet or PC to the Printer
3
-A
Connecting an iOS terminal to the printer
Connect the LAN cable to the printer LAN connector
.
RESET
DC24V
LAN
Cas
h D
raw
er
/Bu
zze
r
0.5A
2.4A
0.5A
iPa
d
LAN
1
2
Connect the other plug to the connector of the router, hub, or other
LAN device
.
Wired LAN
interface
Connect the Lightning cable to the printer USB port (2.4A)
.
2
RESET
DC24V
LAN
Cas
h D
raw
er
/Bu
zze
r
0.5A
2.4A
0.5A
iPa
d
1
2.4A
iPad
Printer-side plug
(Type A)
USB
interface
Printer-side plug
DHCP is enabled by default for the wired LAN settings. To
continually use the same IP address, set a static IP address
before use.
For the static IP address setting procedure, refer to the On-
line Manual.
Connect the other plug to the smartphone/tablet
.
Image of connection
Image of connection
Installing the Printer
Check the Supplied Accessories
Accessories vary depending on the model.
This document explains the procedures for use of mC-Print3. Please store it carefully after reading it.
Note: MCP31L is used for an illustration as representative.
Introduction
Paper Roll
Guide
Paper Roll
Easy
Setup Guide
Safety
Instructions
Power Cable
AC Adapter
Flyer
(Q&A reference)
What the utility can do
The utility can be used to change the settings of the printer and peripheral devices.
Examples) • Bluetooth pairing
• memory switch changes, logo registration
• Bluetooth settings, LAN settings • Sample printing etc.
• Firmware update/diagnosis
●
To use the utility, download it from the site at right.
●
To perform setup using this manual, proceed to Step
1
.
www.star-m.jp/mcprint-app.html
mC-Print3 Utility Download
www.star-m.jp/mcprint3-oml.html
mC-Print3 Online Manual
In Case of Trouble
If you experience trouble with the setup procedure, refer to the Online Manual.
Place the enclosed flyer close to the printer and use it when necessary.
MCP31L
Easy Setup Guide
You will need:
• Commercially available Lightning
cable or Lightning cable that
was provided with the smart-
phone/tablet.
You will need:
• Commercially-available LAN cable
1
Installing the paper roll
Take the slack of the paper roll before paper
setting, insert the paper roll as shown in the
illustration.
Pull the end of the paper roll out straight
,
and use both hands to close the printer cover
.
3
4
4
2
1
Pull the open lever
and open the printer
cover
.
When using a 58 mm roll, install the pro-
vided paper roll guide.
B
A
1
2
With the notch part A (triangle mark) of the
paper roll guide facing down, angle the guide
to the right and insert it
.
Position so that the notch part A is aligned
with the main unit rib B, then slide the guide
from the right
.
When the slid paper roll guide stops, stand
it up vertical
, and press until it clicks into
place
.
To change the paper width, it is necessary to
change the memory switch setting. For de-
tails, refer to the Online Manual.
3
4
2
Turning ON the main unit power
Press the power button
and confirm that
the LED (blue) illuminates
.
4
5
Connect the power cable to the AC adapter
, and connect the cable connector to the
printer as shown in the illustration
. Insert
the plug into the outlet
.
Place your nails into the gaps in the right and
left sides of the rear cover on the back of the
printer, and then remove the cover.
RESET
DC24V
LAN
Cas
h D
raw
er
/Bu
zze
r
0.5A
2.4A
0.5A
iPa
d
1
3
2
USB Cable
