WARNING: Read and understand all instructions.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious personal injury.
Safety Instructions
DANGER: Laser Radiation, avoid direct eye exposure, serious eye injury can result.
• Do not use optical tools such as a telescope or transit to view the laser beam.
• Position the laser so unintentional eye contact will be avoided.
• Do not operate the laser around children or allow children to operate the laser.
• Do not disassemble. Modifying the product in any way can increase the risk of laser radiation.
WARNING:
Use of controls or adjustments or performance of procedures other than those specified
in this manual may result in hazardous laser radiation exposure.
• Do not operate in explosive atmospheres, such as in the presence of flammable liquids, gases, or
dust.
• Use only with the specifically designated batteries. Use of any other batteries may create a risk of
fire.
• Store idle product out of reach of children and other untrained persons. Lasers are dangerous in the
hands of untrained users.
• Use only accessories that are recommended by the manufacturer for your model. Accessories that
may be suitable for one laser, may create a risk of injury when used on another laser.
• Repairs and servicing MUST be performed by a qualified repair facility. Repairs performed by
unqualified personnel could result in serious injury.
• Do not remove or deface warning labels. Removing labels increases the risk of exposure to radiation.
• For indoor use only.
• This product is intended for use in a temperature range of 41°F(5°C) - 104°F(40°C).
CAUTION:
Use caution when drilling, nailing or cutting into walls, floors and ceilings which may
contain electrical wiring or pipes.
Always turn off the power when working near electrical
wires.
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified
in this manual may result in hazardous laser radiation exposure.
The label on your tool may include the following symbols:
V……………………volts
mW ……………………milliwatts
nm …………………wavelength in nanometers
Class2 …………………Class 2 Laser
For your convenience and safety, the following labels are on your laser:
STHT77149
Auto-Levelling Laser with Built In Protractor
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
www.STANLEYTOOLS.eu
79003212
INSTALLING THE BATTERIES - FIGURE A
• Ensure laser on/off actuator
(1)
is in the full off position by sliding the actuator to the left “OFF”
position.
• Open the battery compartment cover
(7
) located on the back of the unit. Insert 2 fresh 1.5 volt AAA
batteries making sure to match (+) and (-) terminals correctly. Close battery compartment cover and
click into place.
WARNING: Batteries can explode, or leak, and can cause injury or fire.
To reduce this risk:
•
Carefully follow all instructions and warnings on the battery label and package.
• Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the
equipment.
• Do not short battery terminals.
• Do not charge batteries.
• Do not mix old and new batteries. Replace all of them at the same time with new batteries of the
same brand and type.
• Remove dead batteries immediately and dispose of per local codes.
• Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
• Remove batteries if the device will not be used for several months.
“Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US Department
of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in
commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries, make sure that the battery
terminals are protected and well insulated from materials that could contact them and cause a
short circuit.”
FEATURES - FIGURE B
1.) On / Off Actuator
6.) Wall Mounting Attachment
2.) Protractor
- (drywall pin and keyhole)
3.) Laser Direction Button - (Left Projection)
7.) Battery Compartment
4.) Laser Direction Button - (Right Projection)
8.) Keyhole Opening
5.) Self-Leveling Laser Lines
9.) Drywall Pin
HANGING ON A WALL USING A SCREW -FIGURE C
The laser unit can be hung on a wall with a screw, using the keyhole opening
(8)
in the wall mounting
attachment.
• Place the keyhole opening over the head of the screw and make sure that the attachment is seated
into the narrow opening of the keyhole.
• Tighten the screw.
• Align the circular pocket on the back of the laser with the magnetic circle on the front of the wall
attachment.
• Make sure that the unit is seated firmly, and is secure on the wall.
HANGING ON DRYWALL SURFACES ONLY - FIGURE D
The laser unit can be hung on drywall, using the drywall pin
(9)
in the wall mounting attachment.
• To press pin into drywall, first expose pin by rotating pin base from opposite side
(Figure D)
.
• While maintaining pressure on pin base, insert pin straight and seat firmly against drywall surface.
• The drywall pin should always be pushed in by hand and never driven by a hammer.
• To remove drywall pin from the wall, pull out straight.
• Avoid exposure-Laser
radiation emitted from this
aperture.
Made in China
Made in China
www.stanleytools.com
www.stanleytools.eu
www.stanleylasers.com
GB
