S
PEED
M
ATE
KNOTMETER/LOG
R
KT
NM
S
PEED
M
ATE
KNOTMETER/LOG
R
S
PEED
M
ATE
KNOTMETER/LOG
R
S
PEED
M
ATE
KNOTMETER/LOG
R
KHM
NM
SM
KM
S
PEED
M
ATE
KNOTMETER/LOG
R
M/S
NM
SM
KM
S
PEED
M
ATE
KNOTMETER/LOG
R
CHOOSING FUNCTIONS AND DISPLAY UNITS:
Pressing and HOLDING the button for more than 3
seconds will cause the display to roll through the
following choices:
Power Off:
Release the button to turn the
unit off. (Note: the unit will also
power down automatically
after 17 minutes of receiving no
button pushes or information
from the speed sensor.)
6/3 Minute Countdown:
Release the button to engage
the 6-minute or 3-minute
countdown timers. See
"Countdown Timer", next page,
for more instructions.
10/5 Minute Countdown:
Release the button to engage
the10-minute or 5-minute
countdown timers. See
"Countdown Timer", next page,
for more instructions.
S
PEED
M
ATE
KNOTMETER/LOG
R
Knots Display:
Release the button to display
speed in knots ("KT") and
distance in nautical mile ("NM").
S
PEED
M
ATE
KNOTMETER/LOG
R
MPH
SM
MPH Display:
Release the button to display
speed in miles per hour
("MPH") and distance in statute
miles ("SM").
KMH Display:
Release the button to display
speed in kilometers per hour
("KMH") and distance in
kilometers ("KM").
M/S Display:
Release the button to display
speed in meters per second
("M/S") and distance in
kilometers ("KM").
Calibration:
Release the button to enter
the calibration function. See
"Calibration", next page, for
more information.
8)
7)
6)
5)
4)
3)
2)
1)
HOLD
HOLD
HOLD
S
PEED
M
ATE
KNOTMETER/LOG
R
KT
NM
HOLD
HOLD
HOLD
HOLD
HOLD
S
PEED
M
ATE
KNOTMETER/LOG
R
KT
NM
S
PEED
M
ATE
KNOTMETER/LOG
R
KT
NM
S
PEED
M
ATE
KNOTMETER/LOG
R
KT
NM
S
PEED
M
ATE
KNOTMETER/LOG
R
KT
NM
S
PEED
M
ATE
R
KNOTMETER/LOG
OPERATING INSTRUCTIONS
S
PEED
T
ECH
I
NSTRUMENTS
10413 Deerfoot Drive, Great Falls, VA 22066 USA
Toll Free (800) 760-0004
ON/START/STOP:
Push and release the button to
turn the unit on.
Push and release AGAIN to start
unit.
Push and release again to stop
unit.
ZEROING:
Hold the button for 2 seconds then
release to zero display and reset
speed memory.
Push and release AGAIN to start
unit.
NOTE: If you hold the button too long, you will enter
function/units selection (see box to the right). Simply release
the button on the desired function or display units.
2
SEC
4
SEC
1
CHOOSING TIME, MAX OR AVERAGE:
Hold the button for 1/2 second (until lower right window
changes) then release to select time, max or average display.
Display mode can be changed at any time.
Time:
Displays running time from
start or the last time the unit
was zeroed.
1)
"MX":
Displays the maximum speed
achieved since start or the
last time the unit was zeroed.
2)
"AV":
Displays the average speed
since start or the last time the
unit was zeroed.
3)
1/2
SEC
1/2
SEC
1/2
SEC
