background image

SERVICE MANUAL (COMMON)

GR1VH CHASSIS

Segment : AS

9-888-790-01

OLED TV

Sony EMCS (M) Sdn. Bhd., SHES-M

© 2021.02

ORIGINAL MANUAL ISSUE DATE: 2021.02

Conditions of Use:
(1) Please use this information only for the purpose of performing repair, maintenance and/or configuration services of the Sony products

(hereinafter the “Repair services”) under the service agreement entered into with the Sony group company (hereinafter the “Service
agreement”). Using this information for any purpose other than the purpose described foregoing is forbidden.

(2) Only the Authorized Servicer’s officers, employees or subcontractors (including their officers and employees) whose duties justify a need-to-

know and who have agreed to hold confidential this information (collectively hereinafter the ”Permitted users”) are permitted to access and
use this information. To disclose or disseminate to any person other than the Permitted users is forbidden.

(3) Destroy or erase any and all portion of this information promptly in an irrecoverable and secure fashion after achieving the purpose

described in Section (1) above.

(4) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior

written permission of the author.

(Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.)

(5) Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address:

[email protected]

(6) In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information.

Revision of Information:
This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before
using it.

SYS SET

2021/02/04 23:38:48 (GMT+09:00)

Summary of Contents for XR-55A90J








































































































Reviews: