![background image](http://html.mh-extra.com/html/sony/icf-c1pj/icf-c1pj_operating-instructions_399861001.webp)
ICF-C1PJ_U2 [US] 4-528-478-
11
(2)
NOTES ON LITHIUM BATTERY
Wipe the battery with a dry cloth to assure a
good contact.
Be sure to observe the correct polarity when
installing the battery.
Do not hold the battery with metallic
tweezers, otherwise a short-circuit may
occur.
Do not expose the battery to excessive heat
such as direct sunlight, fire or the like.
If you have any questions or problems
concerning your unit, please consult your
nearest Sony dealer.
General information
About the battery as a
backup power source
This unit contains a CR2032 battery as a backup
power source to keep the clock and the alarm
operating during a power interruption. (No
Power No Problem system)
When to replace the
battery
When the battery is discharged, “
” appears
on the display.
If a power interruption occurs while the battery
is discharged, the current time and alarm will
be erased.
Note
If “AM 12:00” flashes on the display when the
unit is connected to an AC outlet for the first
time, the battery may be discharged. In this
case, consult your nearest Sony dealer.
Replacing the backup
battery
1
Keep the AC plug connected to the
wall outlet, then open the battery
compartment on the bottom of the
unit.
Fully loosen
the screw.
Push the tab
and pull up
the lid.
2
Remove the old battery by sliding it
out and picking it up.
3
Insert a new battery into the battery
compartment with the
side facing
up.
CR2032
4
Replace the battery compartment lid
and tighten the screw.
5
Press
AM/FM/NATURE SOUND
to
remove “
” from the display.
Notes
When you replace the battery, do not
disconnect the AC plug from the wall outlet.
Otherwise, the current date and time, alarm,
and station presets will be erased.
If the clock is erased while you are replacing
the battery, set the clock again. (See “Setting
the clock manually”)
If the unit will be left unplugged for a long
time, remove the battery to avoid any
damage that may be caused by leakage or
corrosion.
Troubleshooting
Should any problems persist after you have
made the following checks, consult your
nearest Sony dealer.
The clock flashes “0:00” or “AM 12:00”
after a power interruption.
The battery is discharged. Remove the old
battery and insert a new one.
Unsatisfactory reception
Extend the FM wire antenna fully to increase
reception sensitivity.
Connect the supplied AM loop antenna to
the unit. Rotate the antenna horizontally for
optimum reception.
Do not place the AM loop antenna near the
unit or other AV equipment, as noise may
result.
Keep digital music players or mobile phones
away from the AM loop antenna or the FM
antenna, as this may lead to reception
interference.
The alarm does not sound at the preset
alarm time.
Check that “A” or “B” appears on the display.
The radio or Nature Sound alarm is
activated but no sound is emitted at
the preset alarm time.
Check the alarm volume setting.
When daylight saving time (summer
time) begins, the clock does not switch
to daylight saving time (summer time)
automatically.
Make sure the clock is set correctly.
When “Aut
On” appears on the display
after pressing and holding
DST
for more than
2 seconds, the Automatic DST/summer time
function becomes active.
Specifications
Time display
Switch between the 12-hour system (default)
and the 24-hour system.
Frequency range
Band
Frequency
Channel step
FM
87.5 MHz – 108 MHz
0.1 MHz
AM
530 kHz – 1,710 kHz
10 kHz
Speaker
Approx. 4.0 cm (1 5/8 inches) dia., 8 Ω
Power output: 700 mW (at 10% harmonic
distortion)
Power requirements
120 V AC, 60 Hz
For clock back up: 3 V DC, one CR2032 battery
USB power output
USB port (DC OUT 5 V 1.5 A)
Nature Sounds
Sea Waves, Birds, Rain, Brook, Under the Sea
Dimensions
Approx. 114.5 mm
104 mm
100.5 mm
(w/h/d) (4 5/8 inches
4 1/8 inches
4 inches) including projecting parts and
controls
Mass
Approx. 595 g (1 lb 5 oz) including CR2032
battery
Supplied accessories
AM loop antenna (1)
Design and specifications are subject to
change without notice.
Before operating the unit, please read this
guide thoroughly and retain it for future
reference.
For customers who purchased this
product in the USA
Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send
you periodic mailings about new products,
services, and other important
announcements. Registering your product
will also allow us to contact you in the
unlikely event that the product needs
adjustment or modification. Thank you.
Owner’s Record
The model and serial numbers are located on
the bottom of the unit. Record these numbers
in the space provided below. Refer to them
whenever you call upon your Sony dealer
regarding this product.
Model No.
Serial No.
WARNING
To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation of the apparatus with newspapers,
tablecloths, curtains, etc. And do not place
lighted candles on the apparatus.
To reduce the risk of fire or electric shock, do
not expose this apparatus to dripping or
splashing, and do not place objects filled with
liquids, such as vases, on the apparatus.
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
Do not expose batteries or apparatus with
battery-installed to excessive heat such as
sunshine, fire or the like.
As the main plug is used to disconnect the unit
from the mains, connect the unit to an easily
accessible AC outlet. Should you notice an
abnormality in the unit, disconnect the main
plug from the AC outlet immediately.
The unit is not disconnected from the AC
power source (mains) as long as it is connected
to the wall outlet, even if the unit itself has
been turned off.
The nameplate and important information
concerning safety are located on the bottom
exterior.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same type.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The following FCC statement
applies only to the version of
this model manufactured for
sale in the USA. Other versions
may not comply with FCC
technical regulations.
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced
radio/TV technician for help.
WARNING
Do not ingest battery, chemical burn
hazard.
This product contains a coin/button cell
battery. If the coin/button cell battery is
swallowed, it can cause severe internal burns in
just 2 hours and can lead to death.
Keep new and used batteries away from
children. If the battery compartment does not
close securely, stop using the product and keep
it away from children.
If you think batteries might have been
swallowed or placed inside any part of the
body, seek immediate medical attention.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10) Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified
by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
For the state of California, USA
only
Perchlorate Material –special handling may
apply, See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate
License and Trademark
Notice
No Power No Problem™ is a trademark of Sony
Corporation.
Precautions
Operate the unit on the power sources
specified in “Specifications.”
To disconnect the power cord (mains lead),
pull it out by the plug, not the cord.
Do not leave the unit in a location near a
heat source, such as a radiator or airduct, or
in a place subject to direct sunlight, excessive
dust, mechanical vibration, or shock.
Allow adequate air circulation to prevent
internal heat build-up. Do not place the unit
on a surface (a rug, blanket, etc.) or near
materials (a curtain) that might block the
ventilation holes.
Getting Started
Connecting the AM
loop antenna
The shape and the length of the antenna is
designed to receive AM signals. Do not
dismantle or roll up the antenna.
1
Raise the plastic stand and fit the
antenna into the slot of the stand.
Press the
antenna into
the stand
until it clicks.
Plastic stand
2
Insert the AM antenna connector into
the
AM ANTENNA
jack on the unit.
To remove the AM loop
antenna
Push and hold down the tab of the antenna
terminal clamp, and remove the AM loop
antenna.
Connecting to an AC
power source
Connect the AC power cord to a wall outlet.
To wall outlet
“month and day” (about 2 seconds)
“year”
(about 2 seconds)
“current EST (Eastern
Standard Time)” appears on the display in turn.
(This unit is preset to the current EST at the
factory, and is powered by the back-up
battery.)
Setting the clock for
the first time
All you need to do to set the clock for the first
time is select your time zone.
If you live in the Eastern Standard Time zone,
you do not need to adjust the area setting.
1
Press and hold
TIME ZONE
for more
than 2 seconds.
Area number “–5:00” appears on the
display.
2
Press
VOL/SET +
or
–
repeatedly to
select a number as follows:
Area number
Time zone
“–3:30”
Newfoundland Standard
Time
“–4:00”
Atlantic Standard Time
“–5:00”
Eastern Standard Time
(default)
“–6:00”
Central Standard Time
“–7:00”
Mountain Standard Time
“–8:00”
Pacific Standard Time
“–9:00”
Alaska Standard Time
“–10:00”
Hawaii Standard Time
3
Press
SNOOZE/BRIGHTNESS/ENTER
to set.
Note
During shipment and your first use, a clock
error may occur. In this case, refer to “Setting
the clock manually” to set the correct time.
About Automatic DST/
summer time adjustment
This unit automatically adjusts for daylight
saving time (summer time). “DST” automatically
appears on the display at the beginning of
daylight saving time (summer time), and
disappears at the end of daylight saving time
(summer time).
Daylight saving time (summer time) begins
at 2:00 AM on the second Sunday of March.
Standard time begins at 2:00 AM on the first
Sunday of November.
Notes
The implementation of DST/summer time
and its beginning/ending date and time are
subject to circumstances and laws in each
country/region. Should this interfere with the
desired adjustment, cancel the Automatic
DST/summer time adjustment and set the
clock manually as necessary. Customers
living in a country/region that does not use
daylight saving time (summer time) should
cancel the Automatic DST/summer time
adjustment before using the unit.
When Hawaii Standard Time is set, the
default Automatic DST/summer time
adjustment setting is off.
To cancel Automatic DST/
summer time adjustment
The Automatic DST/summer time
adjustment can be canceled.
Press and hold
DST
for more than 2
seconds.
“Aut
OFF” appears on the display.
To reactivate Automatic DST/
summer time adjustment
Press and hold
DST
for more than 2
seconds.
“Aut
On” appears on the display.
This unit includes a preinstalled Sony Lithium battery (CR2032) as a back-up power source for the clock,
which is preset to EST (Eastern Standard Time) at the factory. This battery is considered part of the
product.
This warranty is valid only in the United States.
FM/AM Clock Radio
Operating Instructions
©2014 Sony Corporation Printed in China
4-528-478-
11
(2)
ICF-C1PJ