background image

– 1 –

CD

Model Name Using Similar Mechanism NEW

Section

CD Mechanism Type

KSM-213CDM

Optical Pick-up Name

KSS-213C

TC

Model Name Using Similar Mechanism CFD-V10

Section Tape Transport Mechanism Type

MF-V10-117

SERVICE MANUAL

US Model

Canadian Model

E Model

CFD-S38

CD RADIO CASSETTE-CORDER

Other Specifications
CD player section

System

Compact disc digital audio system

Laser diode properties

Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)

Spindle speed

200 r/min (rpm) to 500 r/min (rpm) (CLV)

Number of channels

2

Frequency response

20 - 20,000 Hz +1/–2 dB

Wow and flutter

Below measurable limit

SPECIFICATIONS

– Continued on next page –

Radio section

Frequency range

FM: 87.6 - 108 MHz
AM: 530 - 1,710 kHz

Aerials

FM: Telescopic aerial
AM: Built-in ferrite bar aerial

Cassette-corder section

Recording system

4-track 2 channel stereo

Fast winding time

Approx. 120 sec. with Sony cassette C-60

Frequency response

TYPE I (normal): 70 - 13,000 Hz

General

Speaker

Full range: 10 cm (4 in.) dia.,
6 ohms, cone type (2)

Outputs

Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones

MICROFILM

AUDIO POWER SPECIFICATIONS (US Model)

POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 6-ohm loads, both channels driven from
100 - 10,000 Hz; rated 4 W per channel-
minimum RMS power, with no more than 10%
total harmonic distortion in AC operation.

Ver 1.2  1999. 09
With SUPPLEMENT-1
(9-926-939-81)

Summary of Contents for CFD-S38 - Cd Radio Cassette-corder















































Reviews: